【正文】 the length of cable should be less than 30m. xiii. 電焊機應正確接地。Cushions and cover would be needed for welding/cutting machine to be used in construction site, in order to prevent machine from being damaged by rain or water. vii. 焊接/切割設備的接線應符合“三相五線制”，一臺設備一個漏電保護器并在設備的外殼做好重復接地。The strength and friction of contact area should be sufficient to ensure stability of objects. xvi. 嚴禁使用起重機械吊運超載或重量不清的物件或埋置物體。起重作業時，指揮人員應穿熒光服。Before use portable generators, chassis must be parked on the basis of the smooth, not allowed to move during , generator when running, even without excitation, should also be considered with in rotating generator online derivation and reach the rotor by hand or cleaning content such as canvas cover shall be used for operation of generator.xi. 發電機經檢修后必須仔細檢查轉子及定子槽間有無工具、材料及其它雜物，以免運轉時損壞發電機。Parallel operation of generator must have been to the normal and stable operation.vi. 接到“準備并聯”的信號后，以整部裝置為準，調整轉速，在同步瞬間合閘。The voltage of power supply of portable lamp should be less than 36V, and metal protecting net will be equipped to lamp bulb. ix. 潮濕環境使用行燈應保證：燈體與手柄堅固、絕緣良好并耐熱耐潮濕；燈頭與燈體結合牢固，燈頭無開關；燈泡外部有金屬保護網；金屬網、反光罩、懸吊掛鉤固定在燈具的絕緣部位上。General lighting, local lighting and mixed lighting should be set up to warehouse, office, materials storage yard, roads, and those places where the natural lighting is poor. ii. 在一個工作場所內，不宜只設局部照明。Strictly prohibit dismantling the electrical configurationRegularly check the antithunder facilities, antistatic facilities to ensure the properties safe and reliable. vi. 配電箱、開關箱應有名稱、用途、分路標記及系統接線圖。The electrical engineer and HSE administrative staff have to make safe and technical disclosure to electric users, and help them understand protential hazards, precautions and emergency measures. All of them have to sign on the disclosure record sheet. Requirements on electricity safety i. 作業人員要遵守各種電氣設備的安全操作規程，使用電氣設備前必須按規定穿戴好相應的個人防護用品，并檢查電氣裝置和保護設施，嚴禁設備帶“缺陷”運轉。Prior to construction, it is necessary to make technical disclosure to all the construction workers, which would be helpful to fully understand the engineering features and measures for construction safety, and pletely and correctly execute these measures during the period of construction. iii. 作業前應對施工區域、作業環境、操作設施、設備、工器具等進行認真檢查，發現隱患立即停 止施工，落實整改后方準施工。special標志牌前不得放置妨礙認讀的障礙物。 welding在水坑內及積水處工作時必須穿防穿刺防水膠靴。Safety goggles and scarfs shall be equipped to workers if any flying objects may be occurred. The relevant face shield also must be equipped to workers when they are welding or cutting something, protective nets or protective barriers have to be set up if necessary. v. 個人防護用品是實現安全生產的一項強制性預防措施，不得隨意變更或降低標準。懸掛式和附著式的固定應穩固不傾斜，柱式的安全標志牌和支架應牢固連接在一起。works (including electrician, welder, craneman, drivers etc.) must accept professional training organized by governments, and obtain the relevant certificate, then they are able to undertake the related works. ii. 項目經理、安全管理人員應經過相關部門培訓，并取得資質證書，方可上崗。Pass should be handled before entering into construction site, besides, it is strictly prohibited to lend Pass to others. vi. 施工現場所用的施工機械、工器具及安全防護用具，必須經有資質檢驗單位的檢驗，符合安 全管理規定方可使用。Measure the insulating properties, such as insulation resistance, pressive strength, leakage current etc, in order to ensure the electrical equipment and power supply and distribution line in good working conditions. iii. 易燃易爆場所裝設的電氣設備必須是防爆型；不得任意拆除電氣設備部件，保持防爆性能。Electrician shall check and repair the power distribution cabinet, swith box every day, and make records.ix. 電工檢查、維修配電箱，開關箱進行時，必須將其前一級相應的電源隔離開關分閘斷電，并上鎖掛牌，嚴禁帶電作業。嚴禁與金屬尖銳斷口、強腐蝕介質和易燃易爆物接觸。Outdoor lamps (220V) should be at least 3m away from the ground, and indoor lamps (220V) should be at least. The distance between lamps and flammable objects should be no less than , besides, some heat insulation measures shall be taken. iv. 金屬鹵化物燈具的安裝高度宜在3米以上，燈線應固定在接線柱上，不得靠近燈具表面。 the bulb holder and housing should be contacted closely etc. x. 防爆場所必須使用防爆型燈具。負荷應逐步增大，力求三相平衡。有功功率通過油門來調節，無功功率通過勵磁來調節。When stopping, load reduction at the first, the excitation rheostat reply, that minimize voltage value, and then in order to cut off the switch, stop at the last .x. 移動式發電機，使用前必須將底架停放在平穩的基礎上，運轉時不準移動。Must be grounding.xiii. 發電機用柴油應存放在陰涼、通風的庫房，遠離火種、熱源。During using crane, it is strictly prohibited standing people. within radius of gyration vi. 吊裝作業時設置警戒區域掛警示牌，非作業人員不得入內。升降、運行應保持同步，每臺起重機械的載荷不宜超過額定起重能力的75%。Pile machine starts, the crew should pay close attention to the trend of the pile machine, if discovery is unusual phenomenon, should immediately stop check, troubleshooting, continuing the construction.ii. 遇有地基超軟弱情況或軟弱不均地段時，應即使調整機體或墊平枕木等，增加地面承載力防止樁機傾倒。Workers in charge of welding/cutting works must be chosen in accordance with relevant requirements of special works, and only qualified workers could work with certificate. ii. 在作業過程中，作業人員必須穿戴符合標準要求的防護服、防護面罩、眼鏡及絕緣靴等專用個人防護用品，必須戴安全帽。Unqualified parts and cables of welding/cutting machine must be timely repaired or replaced, only qualified machines could be put into use. x. 電焊機電源線應選用滿足載荷需要的無接頭的橡皮護套銅芯軟電纜，其性能應符合GB5013《額定電壓450/750V及以下橡皮絕緣電纜》的要求。作業點應提前準備好滅火器、接火毯等消防設施，應提前清理作業點周圍的易燃物品，在危險區域作業，要安排專職監火人。If workers have to leave construction site for a long time, the power supply of welding machine must be shut off. xx. 隨著作業進度清理作業區域，保證現場安全、整潔、文明。Operator is strictly prohibited to leave without permission, it is also not allowed to leave machinery to other irreletive people. v 施工機械應由經過批準的機組人員或專人負責使用和管理，操作人員應遵守保養規定，認真做好各級保養，保持施工機械經常處于完好狀態。Only qualified construction machinery could be put into use. Some safety shield could be installed to rotating parts of construction machinery.ix. 固定式施工機械應安裝在牢固的基礎上。運轉時，不得用手觸摸轉動和傳動部位，嚴禁直接調整運轉皮帶。Reservoir application of steel tube well enclosure in accordance with the requirements, and set up warning signs. 施工能源的使用與管理 Usage and management of construction energy i. 杜絕非環保材料、設備的