常用模具術語專業詞匯中英文翻譯(文件)
【正文】 on Pad 頂出襯墊Ejector 脫模器Ejector Guide Pin 頂出導梢Ejector Leader Bush 頂出導梢襯套Ejector Pad 頂出墊Ejector Pin 頂出梢Ejector Plate 頂出板Ejector Rod 頂出桿Ejector Sleeve 頂出襯套Ejector Valve 頂出閥Eye Bolt 環首螺栓Filling Core 填充型芯 椿入蕊Film Gate 薄膜形澆口Finger Pin 指形梢Finish Machined Plate 角形模板Finish Machined Round Plate 圓形模板Fixed Bolster Plate 固定側模板Flanged Pin 帶凸緣針Flash Gate 毛邊形澆口Flask 上箱Floating Punch 浮動沖頭Gate 澆口Gate Land 澆口面Gib 凹形拉緊楔Goose Neck 鵝頸管Guide Bushing 引導襯套Guide Pin 導梢Guide Post 引導柱Guide Plate 導板Guide Rail 導軌Head Punch 頂頭沖孔Headless Punch 直柄沖頭Heavily Tapered Solid 整體模蕊盒Hose Nippler 管接頭Impact Damper 緩沖器Injection Ram 壓射柱塞Inlay Bush 嵌入襯套Inner Plunger 內柱塞Inner Punch 內沖頭Insert 嵌件Insert Pin 嵌件梢King Pin 轉向梢King Pin Bush 主梢襯套Knockout Bar 脫模杵Land 合模平坦面Land Area 合模面Leader Bush 導梢襯套Lifting Pin 起模頂針 起模桿Lining 內襯Locating Center Punch 定位中心沖頭Locating Pilot Pin 定位導梢Locating Ring 定位環Lock Block 壓塊Locking Block 定位塊Locking Plate 定位板Loose Bush 活動襯套Making Die 打印沖子Manifold Block 歧管檔塊Master Plate 靠模樣板Match Plate 分型板Mold Base 塑膠模座Mold Clamp 鑄模緊固夾Mold Platen 模用板Moving Bolster 換模保持裝置Moving Bolster Plate 可動側模板One Piece Casting 整體鑄件Parallel Block 平行墊塊Parting Line 分模線Parting Lock Set 合模定位器Pass Guide 穴型導板Peened Head Punch 鑲?cè)胧經_頭 錘擊強化沖頭 鉆桿凸模Pilot Pin 定位銷 導向銷子Pin Gate 針尖澆口Plate 襯板Pre Extrusion Punch 頂擠沖頭Punch 沖頭Puncher 推桿Pusher Pin 襯套梢Rack 機架Rapping Rod 起模桿Reentrant Mold 凹入模Retainer Pin 嵌件梢Retainer Plate 托料板Return Pin 回位梢Riding Stripper 浮動脫模器Ring Gate 環型澆口Roller 滾筒Runner 流道Runner Ejector Set 流道頂出器Runner Lock Pin 流道拉梢Screw Plug 頭塞Set Screw 固定螺絲Shedder 脫模裝置Shim 分隔片Shoe 模座之上下模板Shoot 流道Shoulder Bolt 肩部螺絲Skeleton 骨架Slag Riser 冒渣口Slide（Slide Core） 滑塊Slip Joint 滑配接頭Spacer Block 間隔塊Spacer Ring 間隔環Spider 模蕊支架Spindle 主軸Sprue 注道Sprue Bushing 注道襯套Sprue Bushing Guide 注道導套Sprue Lock Bushing 注道定位襯套Sprue Puller 注道拉料 澆道推出桿 注道殘料頂銷Spew Line 合模線Square Key 方鍵Square Nut 方螺帽Square Thread 方螺紋Limit Stop Collar 限位套Stop Pin 止動梢Stop Ring 止動環Stopper 定位停止梢Straight Pin 圓柱銷Stripper Bolt 脫料螺栓Stripper Bushing 脫模襯套Stripper Plate 剝料板Stroke End Block 行程止梢Submarine Gate 潛入式澆口Support Pillar 支撐支柱 頂出支柱Support Pin 支撐梢Supporting Plate 托板Sweep Template 造模刮板Tab Gate 輔助澆口Taper Key 推拔鍵Taper Pin 拔錐梢 錐形梢Teeming Pouring 澆注Three Start Screw 三條螺紋Thrust Pin 推力銷Tie Bar 拉杵Tunnel Gate 隧道形澆口Vent 通氣孔Wortle Plate 拉絲模板模具術語翻譯：動模 Movable Mould Moving Half定模座板 Fixed Clamp Plate Top Clamping Plate Top Plate動模座板 Mov
公司管理相關推薦
鄂ICP備17016276號-1