freepeople性欧美熟妇, 色戒完整版无删减158分钟hd, 无码精品国产vα在线观看DVD, 丰满少妇伦精品无码专区在线观看,艾栗栗与纹身男宾馆3p50分钟,国产AV片在线观看,黑人与美女高潮,18岁女RAPPERDISSSUBS,国产手机在机看影片

正文內容

地下grp管道施工方案-wenkub

2023-05-13 01:44:03 本頁面
 

【正文】 oints installation method of underground GRP piping. This procedure is applicable to all U/G GRP pipe diameters.Related data of U/G piping GRP part is as following:System descriptionMaterial classDiameter rangeConnection MethodW WDGAANA4”,6”,8”,10”,12”,20Butt amp。 wrap joint lamination3. Reference1 The drawing of 080036AADA100201~400207 U/G Composite DWG2 Specification:080036AASG007 Specification for Underground Piping amp。 Wrap Joint Procedure Page 4 to 5.The location of resin, WFluid, catalyst amp。 Wrap Joint Procedure Page 7. Fitting up1 Check the alignment and fixing the pipe ends as close as possible, then prepare the putty.2 Apply the putty with a putty knife filling all the gap。 Wrap Joint Procedure Page 8 to 11 LAMINATION ON THE PIPE JOINT of and attachment B: Installation and Handling Instructions For Rigid Joint Pipe Page 5 to 6.1 Enough catalysted resin should be prepared for about 20 –30 minutes gel time and thorough mixing it.2 Spread a thin layer of catalysted resin directly on the surfaces of the pipe joint laminating area.3 Place of chopped strand mat on the surface of wet out area smoothly and wet it out with the paint wooly roller.4 Continue building by alternating chopped strand mat and woven roving and plete wetting out each one before applying the next ply. No more than 5 plies in one layer. Covered with chopped strand mat.The paint roller roll out over the plies to release big air cavities and any excessive resin. Avoid air getting into the laminate by using steel grooved roller slightly pressed to remove out the air bubbles. The angle of groove roller shall be changed time to time in order to remove the air bubbles in all directions. Keeping in consideration that very limited time has left for the resin to start getting gel, make sure all air bubbles have been taken out prior to start the plies to bee hard. Stop rolling as soon as the resin begin to gel. 5 Continue this procedure until all the sections of the first layer been applied. Make sure that each section overlap with the others at least 5 cm. Let this layer layup cure and cool until it is fortable to touch with the bare hand.Continue using the same procedures with the remaining layers as attachment C: Field lamination( process sheet). Make sure that the last plies of the total layup are chopped strand mat.CAUTION :1 Any kind of movement of pipe section could reduce the bond strength of the initial layup plies have not cured. While the jointing is under progress, the pipes must be restrained before moving.2 Remove the layup if not properly bonded to the pipe, and wash the area with solvent and not to run solvent into uncured. Before applying the layup on this area, insure all solvent has pletely evaporated. Never allow spilled chemical on the pipe surface. This may cause damage to the pipe.3 Each joint lamination team should be formed by at least two workers, trained and skilled.Other details see attachment A: Field Butt amp。 Wrap Joint Procedure Page 12 to 14.13. AttachmentsAttachmentA Field Butt amp。 Glass Reinforcement Container THANKS !!!致力為企業和個人提供合同協議,策劃案計劃書,學習課件等等打造全網一站式需求歡迎您的下載,資料僅供參考可編輯修改。 Catalyst AttachmentEU/G GRP PIPING ORGANIZATION CHARTMaterial ManagerSUN changgenStorage ManagerHU zhongk
點擊復制文檔內容
公司管理相關推薦
文庫吧 www.dybbs8.com
備案圖片鄂ICP備17016276號-1