【正文】 湖 北 汽 車 工 業 學 院 畢 業 論 文 I 摘要 隨著汽車的普及，交通事故也日趨頻繁，人們對汽車安全性的要求也越來越高 。對于這些要求，只有通過對汽車系統動力學的深入研究才能實現。 在多體系統動力學分析軟件中， ADAMS 是車輛動力學中應用最廣，最為著名的一個軟件。 本文 基于多剛體動力學 ADAMS 軟件對汽車制動系統參數進行優化設計。在 ADAMS/Car 模塊中構建整車動力學模型，進行直線制動仿真，分析了影響制動性能的關鍵因素；基于響應面法利用 ADAMS/Insight 模塊對制動系統 前、后制動輪缸活塞面積 ,前、后制動器的摩擦系數 和 前后制動管路壓強分配 系數 進行優化，得到制動距離最短的制動系統優化參數；并對優化前后的制動性能進行對比分析。結果表明：經過優化后的汽車制動性能得到較大改善 。 關鍵詞 ： 盤式制動器；仿真；響應面法；參數優化湖 北 汽 車 工 業 學 院 畢 業 論 文 II Abstract With the popularization of automobile, Traffic accident bees more and more. More powerful technology and methods meet them, and they all based on betterly studing system dynamics of automobile. The software ADAMS, which developed with multibody system dynamics, is the most fashionable and authoritative software in the field of mechanical dynamics design for automotive brake system parameters is discussed in this paper based on multibody dynamic software ADAMS. In ADAMS/Car module, the vehicle dynamic model is built and straight brake simulation is performed, the optimal ranges of main factors are determined after analyzing the factors effecting brake performance. By using response surface methodology a group of optimal parameters is obtained with shortest brake distance in ADAMS/Insight module. The results of simulation are pared with that of the primary is enhanced after optimal design. Keywords: disc brake。 simulation。 response surface methodology。 parameter optimization 湖 北 汽 車 工 業 學 院 畢 業 論 文 III 目錄 摘要 ............................................................................................................................................. I Abstract .....................................................................................................................................II 1 緒論 ........................................................................................................................................ 1 本課題來源及意義 ..................................................................................................... 1 國內外研究現狀及發展趨勢 ..................................................................................... 1 本課題研究的主要內容 ............................................................................................. 3 2 制動系的主要參數及選擇 ................................................................................................... 4 制動力與制動力分配系數 ......................................................................................... 4 同步附著系數 ............................................................................................................. 7 制動器最大 制動力矩 ................................................................................................. 9 3 ADAMS 軟件簡介 ............................................................................................................ 11 ADAMS 軟件概述 .................................................................................................. 11 ADAMS 軟件基本模塊 ......................................................................................... 13 用戶界面模塊 (ADAMS/View).................................................................... 13 求解器模塊 (ADAMS/Solver).................................................................... 14 后處理模塊 (ADAMS/PostProcessor) ....................................................... 15 轎車模塊 (ADAMS/Car)............................................................................... 16 4 基于 ADAMS 的汽車建模 .................................................................................................... 17 主要系統模型 ........................................................................................................... 17 前懸架系統 ..................................................................................................... 17 后懸架系統 ..................................................................................................... 18 轉向 系統 ......................................................................................................... 19 制動系統 ......................................................................................................... 19 整車模型的建立 ....................................................................................................... 20 原車直線制動仿真 ................................................................................................... 21 仿真標準 ......................................................................................................... 21 仿真條件 ......................................................................................................... 22 仿真方法 ......................................................................................................... 22 湖 北 汽 車 工 業 學 院 畢 業 論 文 IV 5 制動系統參數優化設計 ..................................................................................................... 24 優化目標和設計參數 ............................................................................................... 24 優化方法與結果 ....................................................................................................... 25 創建設計矩陣 ............................................................................................... 25 更改設計因素 ............................................................................................... 26 提出并更改響應 ........................................................................................... 28 運行試驗 ....................................................................................................... 29 參數優化前后制動性能對比分析 .......................................................................... 32 6 結論與展望 .......................................................................................................................... 34 論文主要研究重點及結論 ..................