【正文】 黑龍江工程學院本科生畢業設計洗發液瓶蓋注塑模設計畢業論文目 錄摘要 .....................................................................................................................IAbstract ...............................................................II第 1 章 緒論 ........................................................................................................................1 概述 ................................................................................................................................1 設計目的及意義 ............................................................................................................1 我國塑料模具在工業中現狀及展方向 ........................................................................1 塑料模具市場情況 .............................................................................................2 塑料模具水平及發展趨向 .....................................................................................2 存在的問題 ....................................................................................................................3 發展展望 ........................................................................................................................4 設計的研究設想及研究方法 ........................................................................................5 設計的結果及意義 ........................................................................................................5第 2 章 分型面位置以及型腔數量和排列方式的確定 .........................................6 塑件的分析 ....................................................................................................................6 塑件材料的選擇 ............................................................................................................6 丙烯腈一丁二烯一苯乙烯三元共聚物(ABS) ......................................................6 聚苯乙烯(PS) ..........................................................................................................7 聚丙烯(PP) ..............................................................................................................7 注射工藝選擇 ................................................................................................................9 溫度 .........................................................................................................................9 壓力 .........................................................................................................................9 聚丙烯的用途 ..............................................................................................................10 分型面位置的確定 ......................................................................................................11 分型面的基本形式 ...............................................................................................11黑龍江工程學院本科生畢業設計 選擇分型面的基本原則 .......................................................................................12 確定行腔數目和排列方式 ..........................................................................................12 行腔數量的確定 ...................................................................................................12 型腔排列方式的確定 ...........................................................................................12 本章小結 ......................................................................................................................13第 3 章 注射機的選定 ...................................................................................................14 注射量的計算 ..............................................................................................................14 初選注射機的型號和規格 ..........................................................................................14 注射機有關工藝參數的校核 ......................................................................................14 注射量的校核 .......................................................................................................14 注射壓力的校核 ...................................................................................................16 模具閉合厚度的校核 ...........................................................................................16 注射機最大開模行程與模無關時的校核 ...........................................................16 脫模距與模板行程的校核 ...................................................................................17 本章小結 ......................................................................................................................17第 4 章 澆注系統的設計 ...............................................................................................18 澆注系統設計的基本要點 ..........................................................................................18 主流道的設計 ..............................................................................................................18 主流道的作用 .......................................................................................................18 主流道的設計要點 ...............................................................................................19 澆口套結構形式 ...................................................................................................19 澆口的設計 ..................................................................................................................20 澆口的作用 ...........................................................................................................20 澆口的類型 ...........................................................................................................20 澆口設計基本要點 ...............................................................................................20 冷料穴 ..........................................................................................................................21 排氣槽 ..........................................................................................................................21 本章小結 ......................................................................................................................21第 5 章 成型零件的設計及模架的選擇 ....................