底座注塑模的設計-機械專業學位論文范文模板參考資料-文庫吧
2024-11-17 09:01 本頁面
【正文】 ............................................................14 后模仁的設計 .......................................................................................................................22 結 論 ...........................................................................................................................................................27 參考文獻 .......................................................................................................................................................28 致 謝 ................................................................................................................................................ 29 湖北第二師范學院 3 摘 要 塑料工業是當今世界上增長最快的工業門類之一，而注塑模具是其中發展較快的種類，因此，研究注塑模具對了解塑料產品的生產過程和提高產品質量有很大意義。 本論文介紹了注塑成型的基本原理，特別是單分型面注射模具的結構與工作原理，對于注塑產品提出了基本的設計原則，詳細介紹了冷流道注射模具澆注系統、溫度調節系統和頂出系統的設計過程，并對模具強度要求做了說明。設計成型零部件以及設計合理的推出機構。對設計進行驗證主要是對注射機的相關重要參數進行驗證，包括模具閉合厚度、模具安裝尺寸、模具開模行程注射機的鎖模力等。在笑驗 合格后，進行成型零件加工工藝過程的制定，既要保證塑件的質量，又要兼顧經濟性。 最后則是模具的裝配環節，包括制定裝配步驟、明確注意事項等。 通過本設計，可以對注塑模具有一個初步的認識，注意到設計中的某些細節問題，了解模具結構及工作原理 :通過對 Autopsy 的學習，可以建立較簡單零件的零件庫，從而有效的提高工作效率。 關鍵詞：生產工藝 注射莫 成型零件 裝配 塑料模具 分型面 湖北第二師范學院 4 ABSTRACT Plastic in the world today is one of the fastest growing industrial categories, and rapid development of injection mold is one of the species, therefore, the injection mould for understanding the plastic production process and improve product quality has great significance. This paper introduces the basic principle of the injection molding, especially the single parting surface of injection mould structure and working principle for injection products, put forward the basic design principles, introduces in detail the cold runner gating system, injection mould temperature control system and ejection system design process and to mould strength requirement illustrated. Design molding parts and reasonable design launch institutions. To design verification is mainly to the injection machine related important parameter verification, including mold closing thickness, mould installation size, mold cavity trip injection machine clamping force, etc. Laughing after passing inspection for molding parts processing process, both to ensure that the formulation of the quality of plastic parts, and to give consideration to the economy. Finally, is mold assembly link, including setting assembly steps, clear masters needing attention. Through the design of injection mould, can have a preliminary understanding, noticed details in the design of die structure, working principle and understanding to Autopsy learning through, can build a simple parts library, effectively improve the work efficiency. Keyword: production process injection molding part assembly mutual plastic mold parting surface 湖北第二師范學院 5 第一章 擬定模具結構形式 確定型腔數量及排列方式 型腔的數量是由廠方給定，為“一出四”即一模四腔，他們已考慮了本產品的生產批量（大批量生產）和自己的注射機型號。因此我們設計的模具為多型腔的模具。 考慮到模具成型零件和抽芯結構以及出模方式的設計，模具的型腔排列方式如下圖所示： 圖 11
研究報告相關推薦
鄂ICP備17016276號-1