【正文】 ngth steel plate to auto parts, so as to realize the lightweight and high deformation capacity of the body. But the traditional cold stamping technology has been unable to achieve such special steel plate processing, new type of thermal shock technology arises at the historic moment. This technology through special steel heated to 950 ℃ or so, form the austenitizing, then in punching machine for quick stamping forming, and processing of ultra high strength automobile spare parts. Designed by this paper is aimed at the steel plate for the mechanical structural design of the roller bottom furnace heated. Rollerhearth furnace can work according to certain rhythm, a steady stream of steel plate for heating, very conducive to mass production. The overall train of thought of this design USES the modular, subsystem design. Divided into the furnace body, heating, transmission, oven door and accessory, for jacking in a total of five subsystem design. The kiln body with the method of unit assembly, an upgraded version of a subsequent development provides a good range of motion. Finally realize the mechanical structural design of roller hearth furnace. Keywords: Roller hearth furnace。 Heat treatment。 The structure design。 哈爾濱工業大學本科畢業設計（論文） IV 目 錄 摘 要 .......................................................................................................I ABSTRACT........................................................................................... III 第 1 章 緒 論 課題來源及研究的目的和意義 .................................................... 1 課題來源 ................................................................................. 1 研究的目的和意義 ................................................................. 2 國內外在該方向的研究現狀及分析 ............................................ 2 主要研究?jī)?nèi)容 ................................................................................ 2 整個設計任務 ......................................................................... 2 設計任務參數要求 ................................................................. 3 研究方案及預期目標 .................................................................... 4 總體設計方案制定 ................................................................. 4 任務系統劃分 ......................................................................... 4 第 2 章 爐體系統結構設計 爐體結構整體設計 ........................................................................ 6 單節爐體設計 ......................................................................... 6 爐體功能分區 ......................................................................... 6 窯墻材料選擇及尺寸設計 ............................................................ 7 左右側及底面窯墻 ................................................................. 7 窯頂結構 ................................................................................. 8 爐體整體 ................................................................................. 9 爐體鋼架結構 ................................................................................ 9 爐體外框架 ............................................................................. 9 爐體腳支座 ............................................................................. 9 第 3 章 傳動系統結構設計 傳動端結構設計 .......................................................................... 11 傳動參數收集與計算 ........................................................... 11 齒輪設計計算 ....................................................................... 12 小齒輪軸的設計 ................................................................... 16 哈爾濱工業大學本科畢業設計（論文） V 傳動端其他結構設計 ........................................................... 19 從動端結構設計 .......................................................................... 19 鏈輪設計及電機選型 .................................................................. 20 鏈輪設計 ............................................................................... 20 電機選型 ............................................................................... 21 第 4 章 加熱系統結構設計 燃?xì)饧訜嵯到y(tǒng)設計 ...................................................................... 22 管道直徑計算 ....................................................................... 22 燒嘴選型及布置 ................................................................... 22 風機選型計算 ....................................................................... 22 電熱輻射管加熱系統 .................................................................. 22 第 5 章 對中和頂起系統 對中系統結構設計 ...................................................................... 23 定位系統設計 ....................................................................... 23 對中系統設計 ...................................................................... 23 頂起系統結構設計 ...................................................................... 23 第 6 章 爐門及附屬系統結構設計 爐門系統結構設計 ...................................................................... 25 附屬系統結構設計 ...................................................................... 26 結 論 .................................................................................................... 27 參考文獻 ................................................................................................ 29 致 謝 .................................................................................................... 31 哈爾濱