【正文】 c tube 快速接頭：jiffy quick connector plug/socker 四、模具零件：　mold ponents 三板模：3plate mold 二板模：2plate mold 邊釘/導邊：leader pin/guide pin 邊司/導套：bushing/guide bushing 中托司：shoulder guide bushing 中托邊L：guide pin 頂針板：ejector retainner plate 托板：　support plate 螺絲： screw 管釘：dowel pin 開模槽：ply bar scot 內模管位：core/cavity interlock 頂針：　ejector pin 司筒：ejector sleeve 司筒針：ejector pin 推板：stripper plate 縮呵：movable core,return core core puller 扣機（尼龍拉勾）：nylon latch lock 斜頂：lifter 模胚（架）： mold base 上內模：cavity insert 下內模：core insert 行位（滑塊）： slide 鑲件：insert 壓座/斜雞：wedge 耐磨板/油板：wedge wear plate 壓條：plate 撐頭: support pillar 唧嘴： sprue bushing 擋板：stop plate 定位圈：locating ring 鎖扣：latch 扣雞：parting lock set 推桿：push bar 栓打螺絲： 頂板：eracuretun 活動臂：lever arm 分流錐：spure sperader 水口司:bush 垃圾釘：stop pin 隔片：buffle 彈弓柱：spring rod 彈弓:die spring 中托司：ejector guide bush 中托邊：ejector guide pin 鑲針：pin 銷子：dowel pin 波子彈弓：ball catch 喉塞: pipe plug 鎖模塊：lock plate 斜頂：angle from pin 斜頂桿：angle ejector rod 尼龍拉勾：parting locks 活動臂：lever arm 復位鍵、提前回桿：early return bar 氣閥：valves 斜導邊：angle pin 術語：terms 承壓平面平衡：parting surface support balance 模排氣：parting line venting 回針碰料位：return pin and cavity interference ?？偢叱銎C(jī)規格：mold base shut hight 頂針碰運水：water line interferes withejector pin 料位出上/下模：part from cavith (core) side 模胚原身出料位：cavity direct cut on Aplate,core direct cut on Bplate. 不準用鑲件： Do not use (core/cavity) insert 用鈹銅做鑲件： use beryllium copper insert 初步（正式）模圖設計：preliinary (final) mold design 反呵：reverse core 彈弓壓縮量：spring pressed length 穩定性好：good stability,stable 強度不夠：insufficient rigidity 均勻冷卻：even cooling 扣模：sticking 熱膨脹：thero expansion 公差：tolorance 銅公(電極）：copper electrodgearbox復合剖視pound section S0~gX GP Kei`{ r~zM 剖面線section line _6?a2n\ 習慣畫法conventional drawing d!620 虛線dot line, dashed line, hidden line ,Y39。點劃線dash and dot line  ] 波浪線break line dn6N Wnr 剖切平面跡線cutting plane line 9~=/}b8a kV 尺寸dimension size HJ=6`D| 基準datum 9amp。直紋滾花straight knurling s r8yv~P%\ 鍵槽keyway Al9nY$PF/ 拔模斜度pattern draft h h 。填料盒g(shù)land box (8o c3j 油封oil seal OB]n2 螺紋thread NJlT,J 內螺紋internal thread 6[wbk uc 小徑minor diameter v:9(T_^ 牙型form of thread  c_ 螺釘screw N:n_8u 螺母nut 39。墊片washer N39。公差tolerance ov8RP]DL 零線zero line SRaamp。標準公差standard tolerance V?|w9 基本偏差fundamental deviation t|eb1v 間隙配合clearance fit ?\,0aa rQ 過渡配合transition fit yP)Bl*gNI 基軸制shaftbasic system of fits HpTW= 形狀公差tolerance in form, form tolerance 7UOZ|。直線度straightness B64 圓度roundness zCpxSF c 圓柱齒輪cylindrical gear OK4_{s%7 斜齒輪spiral gear grcN39。輪齒gear tooth P0z$_。節圓pitch circle +/LS_Gj 齒根圓root circle, addendum circle M[gF6F |E d 齒高tooth height ]WL? A6JZ A255 齒厚circular thickness E5){5$! 齒寬tooth width L`tupyn sDnAxwy 銷pin 1+4ahzJN
ALL WELDS CONTINUOUS UNLESS OTHERWISE STATED. 未注焊角高3mm.ALL UNSPECIFIED RADI R3 棱角倒鈍CHANNEL 708 角鋼 70X70X8 pitch Tackweld 點焊OD 1/4 尺寸為40,參考值 BSP 扁鋼TYP 2 POSNS 2處11 TOTAL COILS WORKING COILS HAND WOUND ONLY,END COILS SQUARE TO TOUCH.總?cè)?shù)約11圈；工作圈數約9圈；右旋；彈簧的端部磨平以便于接觸.(此為彈簧技術說明)FEMALE: 16