鍛壓機間歇機構設計-展示頁
2025-07-09 09:12本頁面
【正文】 、擠壓、模鍛和粉末冶金等工藝。每一次沖程往往是連續的，當速度較高時由于慣性加工精度較低。subdial。 關鍵詞：機械壓力機；弧面凸輪；分度盤；曲面弧輪AbstractMechanical press is a slidercrank mechanism will be through the motor rotation is converted to linear reciprocating motion of the slider on the billets for the fing forming machine. Mechanical press movements smooth, reliable, widely used in stamping, extrusion, fing and powder metallurgy processes. The content of this research for Fing Machine intermittent transmission case, and its working principle is: by the triangle belt drive motor through the large pulley (usually doubles as a flywheel), after Globoidal cam indexing drive and clutch plates, so that the slider crank drive and convex downlink linear mode. Fing a return after the pletion of the slider upward, the clutch was torn off and the brake at the same time connected to the slider to stop dead in the vicinity. In order to achieve intermittent drive, require the use of space and subdegree Globoidal cam disk, that is, a rotating cam to every point of view only a certain work. Mechanical Press is the impact of the load, that is, a working cycle in the work of fing a short time. Shortterm maximum power than the big ten times more than average power, and therefore need to set the flywheel in the transmission system. By the power of choice to start the motor, the flywheel to the rated speed operation, energy savings. Contact punch began fing billet work, the drive motor power less than the load, lower speed, the flywheel kiic energy released from savings to pensate. Upon pletion of fing, reaccelerate the flywheel energy savings, to prepare for the next use. Mechanical press on the clutch and brake linkage between the device has to ensure that a certain brake clutch engagement before the release, brake before the clutch brake a certain detachment. The operation of the mechanical press is divided into continuous, singleand microtrip, mostly by controlling the clutch and brake to achieve. Production over the possibility of a work force that presses the public phenomenon. In order to ensure equipment safety, in press overload protection device installed.Key words: Mechanical press。 生產中，有可能發生超過壓力機公稱工作力的現象。 機械壓力機上的離合器與制動器之間設有連鎖裝置,以保證離合器接合前制動器一定松開,制動器制動前離合器一定脫開。凸模接觸坯料開始鍛壓工作后，電動機的驅動功率小于載荷，轉速降低，飛輪釋放出積蓄的動能進行補償。短時的最大功率比平均功率大十幾倍以上，因此在傳動系統中需設置飛輪。 為了實現間歇傳動，需要采用空間弧面凸輪和分度盤，即凸輪每旋轉一轉只有一定的角度參加工作。本課題研究的內容為鍛壓機的間歇傳動機構，其工作原理為：由電動機通過三角皮帶驅動大皮帶輪（通常兼作飛輪）,經過弧面凸輪帶動分度盤,驅動曲軸使滑塊直線下行。聊城大學東昌學院本科生畢業論文（設計） 題 目： 鍛壓機間歇傳動機構設計 專業代碼： 0 8 0 2 5 1 作者姓名： 董 志 飛 學 號： 20220020452 單 位： 聊城大學東昌學院 指導教師： 崔 傳 輝 2022 年 5 月 15 日目 錄 言 ...................................................1 發展史及近幾年來國內外發展?fàn)顩r .................................1 設計方案的可行性分析和預期目標 .................................2 設計方案的技術參數 .............................................3 ...........................3 電動機的選用 ...................................................3 帶輪的設計計算 .................................................4 帶輪的計算方法 .............................................4 帶輪的材料選用 .............................................5 帶輪的結構設計 .............................................5 小帶輪連接件的選用 .........................................5 弧面凸輪及分度盤設計計算 .......................................6 弧面凸輪及分度盤運動參數計算[4] ............................6 弧面凸輪及分度盤主要幾何尺寸計算 ...........................7 弧面凸輪的結構圖 ...........................................8 離合器及制動器的選用 ...........................................8 離合器的選用 ...............................................8 制動器
環評公示相關推薦
鄂ICP備17016276號-1