【正文】 stract The graduation design topic is the processing center pound chip breaker structure design. At present, machining center most widely practical automatic chip removal device is scraper chip this rejection chip chip removal efficiency is higher, row crumbs ability is stronger, and the region as a whole did not accumulate chip dead, and strong ability to adapt. However, the chip is not high, the smaller granular chip is easy to cut into the cutting fluid through the hole in the scraper, and thus the machining process is affected.. Chip solution for small particles of chips, there are mainly two kinds of magic separation and filtration. The purpose of this paper is based on several rows of chip structure analysis, pares their respective advantages and disadvantages, and the bination, improve the application in machining center thoroughly swarf filtration can be achieved. In this process, familiar with the structure of the general mechanical structure design process, and through the form of threedimensional and twodimensional map. My main design content for the entire mechanical system, the structure, the transmission design, selection including motor, reducer selection, V belt transmission design, scraper chain transmission design, magic row chip structure design, filter paper scraps discharge structure design and row chip appearance, water tank node structure design. Design thinking is starting from the row removal machine performance and the movement, and to the national quality and technical performance close to the design requirements of chip machine based, and hope to 蘇州科技學院本科生畢業設計（論文） IV design market demand for machining center posite chip removal device. Key word： Machining center， Chip device， Mechanical system蘇州科技學院本科生畢業設計（論文） V 目 錄 第一章 緒論 ............................................................................................................ 1 研究目的與意義 .......................................................................................... 1 排屑器 發展 現狀 .......................................................................................... 1 排屑裝置的發展趨勢 ................................................................................... 3 第二章 粗屑排屑設計 .............................................................................................. 4 總體方案的確定 .......................................................................................... 4 電動機、減速機的選擇： ............................................................................ 5 V 帶的設計計算 ........................................................................................ 6 帶傳動方案的確定 ..................................................................................... 6 帶傳動設計計算 .......................................................................................... 6 帶輪的結構設計 .......................................................................................... 8 鏈傳動設計計算 ........................................................................................ 10 鏈輪結構設計 ........................................................................................... 12 主動鏈輪結構設計 ........................................................................... 12 刮板鏈設計 ................................................................................................ 15 鏈輪軸的設計 ........................................................................................... 17 各軸運動與動力參數 ..................................................................... 17 軸 4 結構設計計算 ........................................................................ 18 軸 5 的設計計算 ............................................................................ 19 軸 6的設計計算 ............................................................................ 20 軸 6的校核 ................................................................................... 22 軸承的校核 ............................................................................................. 23 軸 4 上軸承的校核 ................................................................................... 24 鍵的選擇和校核 ...................................................................................... 24 軸 4 上鏈輪處的鍵 ................................................................................... 24 排屑裝置鈑金結構設計 ............................................................................. 25 第三章 鐵磁性屑排屑設計 ...................................................................................... 26 磁性分離器簡介 ......................................................................................... 26 磁性分離器結構設計 .................................................................................. 26 總體方案設計 .................................................................................. 26 蘇州科技學院本科生畢業設計（論文） VI 工作原理 ......................................................................................... 27 電動機、減速機的選擇 .................................................................... 27 傳動結構設計 ............................................................................................ 29 第四章 微小切屑排屑設計 ...................................................................................... 30 紙帶過濾機介紹 ......................................................................................... 30 方案設計 ................................................................................................... 30 第五章 復合排屑結構設計 ...................................................................................... 32 水箱結構設計 .................................................................................................. 32 結 論 .................................................................................................................... 34 致 謝 .........................................................................