【正文】 accessoriesC基礎復查Check of foundationC機組安裝Installation of machine setAR灌漿前檢查Inspection before groutingAR聯軸節對中Centering of couplersAR機組安裝完整性確認Integrity of machine set installationB機組拆檢組裝情況Disassembling, inspecting and assembling of machine setCR油系統沖洗Flushing of oil systemA油系統整定Setting of oil systemB冷卻系統Cooling systemC冷凝真空系統Condensing vacuum systemB控制和保護系統Control and protection systemB盤車裝置檢查Idle rotating deviceC試運轉Test runAR加注油情況Oiling condition部 位Location油 標 號Mark of oil合格證號Certificate No.注油數量Oiling quantity簽名/日期Signature/Date備注：Remarks表H203機組安裝找正記錄Alignment record for installation of machine set項目：Project裝置：Unit工號：Section位 號Location No.名 稱Name執行標準Standard for execution項 目Item允許偏差(mm)Tolerance 實際偏差 （mm）Actual deviation標 高Elevation中心線Center line縱 向Longitudinal橫 向Transverse水平測量 (mm/m）Leveling12345678910縱 向Longitudinal允許值Allowable value實測值Measured value橫 向Transverse允許值Allowable value實測值Measured value附圖：Attached diagram承包單位代表Contractor representative施工單位Subcontractor施工人Operator建設單位代表Owner representative檢查員Inspector表H204大型機械灌漿前檢查記錄Inspection record before grouting of large machinery項目：Project裝置：Unit工號：Section位 號Location No.名 稱Name執行標準Standard for execution隱蔽前檢查：Inspection before concealing： 布置□ 接觸面□ 焊接□Shims Layout Contact face Welding□ □Anchoring bolt Bolt hole and foundation surface cleanliness： 平墊鐵 斜墊鐵 Specification of shims Flat shims Tapered shims附圖：Attached diagramNo.hnLNo.hnLNo.hnL 施工人： Operator上項工程經檢查符合設計（規范）要求，可以隱蔽。 pipeline□C材料交接檢查Acceptance of material□C基層表面檢查Base course surface□CR絕緣層檢查Insulating layer□BR防潮層檢查Dampproof course□CR保護層檢查Protective course□BR機械位號或管線號Machine equipment or pipeline No.基層表面Base course surface絕緣層Insulating layer防腐蝕面層Anticorrosion finishing course備注Remarks處理方法Treatment method結果Result名稱Name厚度(mm) Thickness結果Result名稱Name厚度(mm) Thickness結果Result技術負責人Technical person in charge質量檢查員Inspector施工人Operator表H201機 泵安裝工序質量控制表Quality control table for machine and pump installing procedures項目：Project裝置：Unit工號：Section位 號Location No.名 稱Name工作介質Medium驅動機類型Type of driver傳動方式Transmission mode執行標準Standard for execution檢 查 項 目Inspection item等級Grade簽名/日期Signature/Date施工單位Subcontractor承包單位Contractor建設單位Owner機器及附件接收Acceptance of machine and accessoriesC基礎復查Check of foundationC機泵安裝Installation of machine and pumpCR灌漿前檢查Inspection before groutingA拆洗及回裝Disassembling, cleaning and reassemblingC(CR)聯軸節對中Centering of couplersB傳動裝置檢查Transmission gearC潤滑油系統檢查、注油Lubrication system inspection and oilingC冷卻、密封系統檢查Cooling and sealing systemC試運轉Test runAR找 正 偏 差Alignment deviation對 中 偏 差Centering deviation位 置Location允 差Tolerance0O～180 O90O～270 O配管前Before pipe assembling配管后After pipe assembling水 平Horizontal位置Location允 差Tolerancea1a2a3a4a1a2a3a4中 心Center徑 向Radial標 高Elevation軸 向Axial試運轉Test temp介質：Medium持續時間：Time duration 從驅動機方向讀數 a1 Reading in direction of driver 百分表固定端： 。 pipeline□C材料交接檢查Acceptance of material□C基層表面檢查Base course surface□CR配料比檢查Mixture ratio□C絕緣層檢查Insulating layer□CR防腐蝕面層檢查Anticorrosion finishing course□BR外觀檢查Visual inspection□C設備位號或管線號Equipment location No. or pipeline No.基層表面Base course surface絕緣層Insulating layer防腐蝕面層Anticorrosion finishing course備注Remarks處理方法Treatment method結果Result名稱Name層數/厚度(um) Number of layers and thickness結果Result名稱Name層數/厚度(um) Number of layers and thickness結果Result合格底漆2/103合格面漆2/101合格技術負責人Technical person in charge質量檢查員Inspector施工人Operator表H126防 腐 層電火花檢測報告Electric spark test reportof anticorrosion layer項目：Project裝置：Unit工號：Section委托單位Truster試驗編號Test No.執行標準Standard for execution檢件名稱Name of specimen防腐區段Anticorrosion section防腐等級Anticorr