【正文】 ect裝置：Unit工號：Section 表H—201 Tab. 機 泵 安裝工序質量控制表Quality control table for machine and pump installing procedures項目：Project裝置：Unit工號:Section位 號Location No.名 稱 Name工作介質Medium驅動機類型Type of driver傳動方式Transmission mode執行標準`Standard for execution檢 查 項 目Inspection item 等級 Grade簽名/日期 Signature/date 施工單位Subcontractor監理單位Contractor建設單位 Owner機器及附件接收Acceptance of machine and accessoriesC基礎復查Check of foundationC機泵安裝Installation of machine and pumpCR灌漿前檢查Inspection before groutingA拆洗及回裝Disassembling, cleaning and reassembling(C)CR聯軸節對中Centering of couplersB傳動裝置檢查Transmission gearC潤滑油系統檢查、注油Lubrication system inspection and oiling C冷卻、密封系統檢查Cooling and sealing system C試運轉Test runAR找正偏差A(yù)lignment deviation對中偏差Centering deviation位置Location允差Tolerance0176。__180176。90176。270176。配管前Before pipe assembling配管后After pipe assembling水平Horizontal位置Location允差Tolerancea1a2a3a4a1a2a3a4中心Center徑向Radial標高Elevation軸向Axial試運轉Test temp介質:Medium持續時間:Time duration 從驅動機方向讀數 Reading in direction of driver百分表固定端:____Fixed end of dial indicator聯軸節間距:_____mmSpacing of couplers a= tgθ=機器軸承溫度Machine bearing temp.前: ℃Front 后: ℃Rear驅動機軸承溫度Driver bearing temp前: ℃Front 后: ℃Rear壓力Pressure進: MPaIn出: MPaout電機溫升: ℃Motor 電流(啟動/運轉): ACurrent(starting/running)備注:Remarks 表H—202 Tab.機 組安裝工序質量控制表Quality control table for machine set installing procedures項目：中鹽吉蘭泰PVC項目Project裝置：年40萬噸PVCUnit工號： 溴化鋰制冷Section位號Location No.名稱Name冷水機組執行標準Standard for execution驅動機Driver主機Host machine種類Type型號Model種類Type型 號Model功率Power轉速Rotating SpeedR/min介質Medium檢查項目Inspection item等級Grade簽名/日期Signature /date施工單位Subcontractor監理單位Contractor建設單位Owner機器及附件接收Acceptance of machine set amp。 accessoriesC基礎復查Check of foundationC機組安裝Installation of machine set AR灌漿前檢查Inspection before groutingAR聯軸節對中Centering of couplersAR機組安裝完整性確認Integrity of machine set installationB機組拆檢組裝情況Disassembling inspecting and assembling of machine set CR油系統沖洗Flushing of oil systemA油系統整定Setting of oil systemB冷卻系統Cooling systemC冷凝真空系統Condensing vacuum systemB控制和保護系統Control and protection systemB盤車裝置檢查Idle rotating device C試運轉Test runAR加注油情況Oiling condition部位Location油標號Mark of oil合格證號Certificate No.注油數量Oiling quantity簽名/日期Signature/date備注:Remarks 表H—203 Tab.機 組安裝找正記錄Quality control table for machine set installing procedures項目：中鹽吉蘭泰PVC項目Project裝置：年40萬噸PVCUnit工號： 溴化鋰制冷Section位號Location名稱Name執行標準Standard for execution項 目Item允許偏差(mm)Tolerance 實 際 偏 差 (mm)Actual deviation 標 高 Elevation中心線Center line 縱向 Longitudinal 橫向 Transverse 水平測量 (mm/m) Leveling 縱 向Longitudinal 允許值A(chǔ)llowable value12345678910 實測值Measured value橫 向Transverse 允許值A(chǔ)llowable value 實測值Measured value 附 圖:Attached diagram監理單位代表Contractor representative施工單位Subcontractor施工人Operator建設單位代表Owner representative檢查員Inspector 表H—204Tab.大型機械灌漿前檢查記錄Inspection record before grouting of large machinery項目：中鹽吉蘭泰PVC項目Project裝置：年40萬噸PVCUnit工號: 溴化鋰制冷Section位號Location No.名稱Name執行標準Standard for execution 隱蔽前檢查: Inspection before concealing 墊鐵： 布置 接觸面 焊接 Shims Layout Contact face Welding 地腳螺栓 螺栓孔及基礎表面清潔 Anchoring blot Bolt hole and foundation surface cleaniness 墊鐵規格： 平墊鐵 斜墊鐵 Specification of shims Flat shims Tapered shims 附圖： Attached diagramNo.hnLNo.hnL 施工人： Operator 上項工程經檢查符合設計（規范）要求