freepeople性欧美熟妇, 色戒完整版无删减158分钟hd, 无码精品国产vα在线观看DVD, 丰满少妇伦精品无码专区在线观看,艾栗栗与纹身男宾馆3p50分钟,国产AV片在线观看,黑人与美女高潮,18岁女RAPPERDISSSUBS,国产手机在机看影片

正文內容

英文版汽車構造-資料下載頁

2025-07-27 18:00本頁面
  

【正文】 d to free energy causes force vibration . Valvetrain assemblies with overhead camshafts can be represented with sufficient accuracy by a 1mass system ( consisting of the moving mass , the valvetrain assembly stiffness and corresponding damping ) .For system with valve bottommounted camshaft and push rods , a 2mass system is being increasingly used . The maximum permissible contact stress , usually regarded as the parameter which limits camlobe radius and the rate of opening on the flank , currently lies between 600700Mpa depending upon the material parings used . Camshaft Drive MechanismEach cam must revolve once during the fourstroke cycle to open a valve. A cycle, remember, corresponds with two revolutions of the crankshaft . Therefore, the camshaft must revolve at exactly half the speed of the crankshaft . This is acplished with a 2:1 gear ratio .A gear connected to the camshaft has twice the number of teeth as a gear connected to the crankshaft. The gears are linked in one of three ways: DriveA cogtype belt can be used .Such belts are made of synthetic rubber and reinforced with internal steel or fiberglass strands. The belts have teeth ,or slotted spaces to engage and drive teeth on gear wheels. A belt typically is used on engines with overheadcam valve trains. DriveOn some engines, a metal chain is used to connect the crankshaft and camshaft gears. Most pushrod engines and some OHC engines have chains. DriveThe camshaft and crankshaft gears can be connected directly, or meshed. This type of operating linkage monly is used on older sixcylinder, inline engines. A camshaft driven by a chain or belt turns in the same direction as the crankshaft . But a Camshaft driven directly by the crankshaft gear turns in the opposite direction. Timing belts are used because they cost less than chains and operate more quietly. A typical timing belt is made of neoprene (synthetic rubber) reinforced with fiberglass. Electronic Valve Control SystemAn electronic value control (EVC) system replaces the mechanical camshaft, controlling each value with actuators for independent value timing. The EVC system controls the opening and closing time and lift amount of each intake and exhaust valve with independent actuators on each value. Changing from a mechanical camshaft driven value into independently controlled actuator valves provides a huge amount of flexibility in engine control strategy. Vehicles utilizing EVC can realize several benefits including:1) increases engine power and fuel economy,2) allows centralized and distributed EVC systems to perform at their full potential,3) adapts to engines of varied cylinder counts.With all of the improved efficiencies and consumer benefits, auto manufacturers are eager to get their first EVC systems on the road. The EVC system is targeted to operate in temperatures up to 125, while the actuator is targeted to run up to 6000 r/min. The actuator can be controlled in a centralized system with a highspeed multiplex bus (up to 10Mbps) or in a distributed system with a nominal speed bus.EVC systems must be pact in size, specifically the actuators that must be small enough to fit in the engine space. A vehicle that uses a 42V system is ideal for EVC because it requires high voltage to control the value actuators, and EVC is targeted for V8 and V12 engines. The EVC system is also highly flexible, allowing adaptability for a number of cylinder engines. New Wordscoordinate 協調valve train 氣閥傳動respectively 分別的,各自的overhead camshaft 頂置凸微輪軸guide 導管tappet 挺桿valve insert 氣門座cotter 鎖銷,鎖片opening 口lobe 凸起spot 點,位置stem 桿dual 雙的cam follower 凸輪挺桿seesaw 蹺蹺板,杠桿value clearance 氣門間歇gastight seal 氣封liable to 容易likelihood         可能 tapping 輕敲valve timing 配氣正時 intake valve 進氣閥 exhaust valve 排氣閥static 靜態的,靜力的kinetic (運)動的,動力(學)的volumetric 測定體積的leverage 杠桿作用offset 偏移量dynamics 動力學valve lift 氣門挺桿valve…as… 把…..看成……parameter 參數,參量radius 半徑,范圍 flank 側面 pairing 配對,成對 correspond with 相當于 gear ratio 傳動比 cogtype belt 齒型帶synthetic rubber 合成橡膠reinforce 加強fiberglass 玻璃纖維strand 繩,線,絞合 slotted 有槽的,切槽的mesh 相嚙合linkage 聯動 inline engine 直列發動機 neoprene 氯?。ǘ。┫鹉zelectronic valve control (EVC) 電子式氣閥控制 centralized system 集中系統distributed system 分布系統 varied cylinder count 可變的汽缸數architecture 結構,構造processor 處理器 local node 局域節點 munication layer 通信層synchronization 同步 Review Question1. List the main parts of the OHC valve train .2. How does a pushrod valve train work ?3. how are the valve clearance adjusted by hand ?4. Why do the intake valves open before TDC and close after BDC ? 5. What do we mean by “ valve overlap “6. Why do most cars use timing belts rather than chains ?7. What a
點擊復制文檔內容
研究報告相關推薦
文庫吧 www.dybbs8.com
備案圖鄂ICP備17016276號-1