【正文】 ctual deviation標 高Elevation中心線Center line縱向Longitudinal橫向Transverse水平測量 （mm/m）Levelling12345678910縱向Longitudinal允許值Allowable value實測值Measurd value橫向Transverse允許值Allowable value實測值Measurd value附圖：Attached diagram監理單位Management施工單位Subcontractor建設單位Owner 總包單位Contractor 表H204Tab.SCC CNCEC 大型機械灌漿前檢查記錄Inspection record before grouting of large machinery項目：Project裝置：Unit工號：Section位號Location No.名稱Name執行標準Standard for execution隱蔽前檢查Inspection before concealing墊鐵： 布置□ 接觸面□ 焊接□ Shims Layout Contact face Welding地腳螺栓□ 螺栓孔及基礎表面清潔□ Anchoring bol t Bolt hole and foundation surface cleanliness墊鐵規格： 平墊鐵 斜墊鐵 Specification of shims Flat shims Tapered shims附圖：Attached diagramNohnLNohnLNohnL施工人Operator以上工程經檢查符合設計（規范）要求，可以隱蔽。The above work conforming to the requirement of design (code) may be concealed 年 月 日 Date建設單位Owner監理單位Management總包單位Contractor 施工單位Subontractor 表H205Tab.SCC CNCEC 機器拆檢及組裝間隙測量記錄Clearance measurement record for disassem bling, inspecting and assembling of machine項目：Project裝置：Unit工號：Section位號Location No.名稱Name執行標準Standard for execution間隙測量部位Clearance measured location規定值(mm)Specified value拆前間隙(mm)Clearance before disassembing組裝后間隙(mm)Clearance after disassembing日期Date注：間隙測量部位另附圖（如果需要）。Note: Clearance measured location has diagram attached ( if necessary )檢查員Inspector施工人Operator表H206Tab.SCC CNCEC 電機空氣間隙測量記錄Air gap measurement record for motor項目：Project裝置：Unit工號：Section位號Location No.名稱Name執行標準Standard for execution按定子上標定的一點盤車檢查空氣間隙 單位：(mm)Inspection of air gap at specified point on the stator by idle rotating Unit部 位Location1234567891011121314151617181920實測值Measured value按轉子上標定的一點盤車檢查空氣間隙 單位：(mm)Inspection of air gap at specified point on the rotor by idle rotating Unit部 位Location12345678910實測值Measured value總包單位Contrator representative檢查員Inspector施工人Operator表H207Tab.SCC CNCEC 機組對中記錄Alignment record for machine set項目：Project裝置：Unit工號：Section位號Location No.名稱Name執行標準Standard for execution聯軸器布置簡圖：Diagram of coupler location對中情況：Alignment a1 b1 a4 a2 b4 b2 a3 b3 單位：(mm) Unit徑向 軸向Radial Axial聯軸器編號Coupler No.徑向Radial軸向Axial端面間隙Clearance at end百分表固定位置Fixed position of dial indicator允許偏差Tolerancea1a2a3a4允許偏差Toleranceb1b2b3b4規定值Stipulated value實測值Measured value備注：Remarks監理單位Management施工單位Subcontractor建設單位Owner 總包單位Contractor 表H209Tab.SCC CNCEC機器試運轉報告Testrun report for machine項目：Project裝置：Unit工號：Section位 號Location No.名 稱:Name部于 位Location試車類別Type of testrun日 期Date執行標準Standard for execution時間Time轉速Speedr/min介質Medium潤滑油Lubricant軸承溫度Bearing temp. (℃)軸振動Shaft vibration(mm)軸位移Shaft displacement(mm)備注Remarks溫度Temp.(℃)壓力Pressure(Mpa)溫度Temp.(℃)壓力Pressure(Mpa)前Front后Rear進In出Out進In出Out進In出Out進In出Out試運轉結果Result of testrun監理單位Management施工單位Subcontractor建設單位Owner 總包單位Contractor 表H210Tab.SCC CNCEC大型軸流風機安裝工序質量控制表Quality control table for installingprocedures of large axial flow blower項目：Project裝置：Unit工號：Section位 號Location No.傳動方式Mode of transmission名 稱:Name執行標準Standard for execution檢查項目Inspection item等級Grage簽字/日期Signature/Date施工單位Subcontractor總包單位Contractor監理單位Managemen建設單位Owner機器及附件接收Acceptance of machine and accessoriesC基礎驗收Check of foundationC機器安裝Installation of machineCR驅動機對中Alignment of driverC灌漿前檢查Inspection before grouting