【正文】 章 3 TurningThe engine lathe, one of the oldest metal removal machines, has a number of useful and highly desirable attributes. Today these lathes are used primarily in small shops where smaller quantities rather than large production runs are encountered.普通車床作為最早的金屬切削機床的一種，目前仍然有許多有用的和為人要的特性和為人們所需的特性。現在，這些機床主要用在規模較小的工廠中，進行小批量的生產，而不是進行大批量的和產。The engine lathe has been replaced in today’s production shops by a wide variety of automatic lathes such as automatic of singlepoint tooling for maximum metal removal, and the use of form tools for finish on a par with the fastest processing equipment on the scene today.在現代的生產車間中，普通車床已經被種類繁多的自動車床所取代，諸如自動仿形車床，六角車床和自動螺絲車床?，F(xiàn)在，設計人員已經熟知先利用單刃刀具去除大量的金屬余量，然后利用成型刀具獲得表面光潔度和精度這種加工方法的優點。這種加工方法的生產速度與現在工廠中使用的最快的加工設備的速度相等。Tolerances for the engine lathe depend primarily on the skill of the operator. The design engineer must be careful in using tolerances of an experimental part that has been produced on the engine lathe by a skilled operator. In redesigning an experimental part for production, economical tolerances should be used.普通車床的加偏差主要信賴于操作者的技術熟練程度。設計工程師應該認真地確定由熟練工人在普通車床上加工的試驗件的公差。在把試驗伯重新設計為生產零件時，應該選用經濟的公差。Turret LathesProduction machining equipment must be evaluated now, more than ever before, this criterion for establishing the production qualification of a specific method, the turret lathe merits a high rating.六角車床 對生產加工設備來說，目前比過去更注重評價其是否具有精確的和快速的重復加工能力。應用這個標準來評價具體的加工方法，六角車床可以獲得較高的質量評定。In designing for low quantities such as 100 or 200 parts, it is most economical to use the turret lathe. In achieving the optimum tolerances possible on the turrets lathe, the designer should strive for a minimum of operations.在為小批量的零件（100~200件）設計加工方法時，采用六角車床是最經濟的。為了在六角車床上獲得盡可能小的公差值，設計人員應該盡量將加工工序的數目減至最少。Automatic Screw Machines Generally, automatic screw machines fall into several categories。 singlespindle automatics, multiplespindle automatics and automatic chucking machines. Originally designed for rapid, automatic production of screws and similar threaded parts, the automatic screw machine has long since exceeded the confines of this narrow field, and today plays a vital role in the mass production of a variety of precision parts. Quantities play an important part in the economy of the parts machined on the automatic screw machine. Quantities less than on the automatic screw machine. The cost of the parts machined can be reduced if the minimum economical lot size is calculated and the proper machine is selected for these quantities.自動螺絲車床 自動螺絲車床通被分為以下幾種類型：單軸自動、多軸自動和自動夾緊車床。自動螺絲車床最初是被用來對螺釘和類似的帶有螺紋的零件進行自動化和快速加工的。但是，這種車床的用途早就超過了這個狹窄的范圍?，F(xiàn)在，它在許多種類的精密零件的大批量生產中起著重要的作用。工件的數量對采用自動螺絲車床所加工的零件的經濟性有較大的影響。如果工件的數量少于1000件，在六角車床上進行加工比在自動螺絲車床上加工要經濟得多。如果計算出最小經濟批量，并且針對工件批量正確地選擇機床，就會降低零件的加工成本。Automatic Tracer Lathes Since surface roughness depends greatly on material turned, tooling , and feeds and speeds employed, minimum tolerances that can be held on automatic tracer lathes are not necessarily the most economical tolerances.自動仿形車床 因?yàn)榱慵谋砻娲植诙仍诤艽蟪潭壬先Q于工件材料、刀具、進給量和切削速度，采用自動仿形車床加工所得到的最小公差一定是最經濟的公差。In some cases, tolerances of are held in continuous production using but one cut . groove width can be held to on some parts. Bores and singlepoint finishes can be held to . On highproduction runs where maximum output is desirable, a minimum tolerance of is economical on both diameter and length of turn.在某些情況下，在連續生產過程中。對于某些零件。鏜孔和休用單刃刀具進行精加工時。在希望獲得最大主量的大批量生產中