一種無線數據采集和傳輸系統的設計-外文翻譯-其他專業-資料下載頁
2025-01-19 00:29本頁面
【導讀】在現代無線通信領域主要有一些技術為無線傳輸網絡提供解決方法，例如：GSM，CDMA，3G，Wi-Fi。這些方法使得網絡能夠高效率和高質量的工作，因此要低成本和在沒有基礎設施或者基礎設施被破壞的情況下推廣它。然后提出了一個對無線通信可行的解決方案，這個方案優。勢在于更強的實時響應，更高的可靠性要求和更小的數據量。通過軟件和硬件的調試。經成功的應用到無線車輛系統。它們也有高成本的缺點，因此如果廣泛的。應用，將會引起大量的資源浪費，也不能在小區域，低速率的數據通信中得到提升。多點短距離無線數據采集和傳輸網絡將成為最佳解決方案。此系統支持點對點，點對。另外，中央監控系統與遠程終端單元進行雙向通信。理層）和第二層而設計的，如圖2所示。然而通信協議里的數據鏈路層是由軟件來實現的。本設計以射頻收發芯片nRF905為核心,以模塊搭建設計為指導。為了方便起見，每個
【正文】 n internally available for parallel processing. Here we already see an important point, that must be considered in the philosophy of SPI bus systems: The length of the shift registers is not fixed, but can differ from device to device. Normally the shift registers are 8Bit or integral multiples of it. Of course there also shift registers with an odd 9 number of bits. For example two cascaded 9Bit EEPROMs can store 18Bit data. If a SPI device is not selected, its data output goes into a highimpedance state, so that it does not interfere with the currently activated devices. When cascading several SPI devices, they are treated as one slave and therefore connected to the same chip select [5]. In figure 4 the cascaded devices are evidently looked at as one larger device and receive therefore the same chip select. The data output of the preceding device is tied to the data Ⅴ .SYSTEM TESTING Because munication between any two nodes may be tested through point to point, in this system Testing Process, munication model between node A and node B is a good example for testing schematic diagram, just like figure 10. Closedloop testing circuit is put up through PC with double serial ports and two RS232 ports and munication node A and B. On one terminal, data was sent through serial port testing auxiliary tool “serial port assistant ”, on the other terminal, returning data is monitored. Data is sent through PC’s serial port A, RS232 port, then data buffer and finally wireless transceiver module successively. However, the process of data receiving was SPI serial, data buffer, then RS232 port, finally PC. In t In this paper, a lowpowered and highperformance wireless data munication system were designed with the principle of transceiver nRF905 and 51 series of singlechip puter as the core hardware. An available solution to the wireless data munications was put forward, and this solution was good at stronger realtime response, higher reliability requirement and smaller data amount, which is widely applied various fields such as data munications, environmental monitoring and security Guard System. We believe that integrated and intelligent Communication Protocol are realized after software design is refined and improved testing process, digital oscilloscope was also used to monitor the data transfer of munication node A , node B , RS232 port and SPI port. In the following section, information from MOSI/SCK and MISO/SCK was analyzed to verify the system’s Correctness. As a waveform of wireless sending data, figure 11 demonstrate some relations among efficient data, address information and synchronous clock in wireless sending process. Because the receiver address must be designated by the transmit terminal, 4 byte address require to be sent after sending packet. Ⅵ .CONCLUSION In this paper, a lowpowered and highperformance wireless data munication system were designed with the principle of transceiver nRF905 and 51 series of singlechip puter as the core hardware. An available solution to the wireless data munications 10 was put forward, and this solution was good at stronger realtime response, higher reliability requirement and smaller data amount, which is widely applied various fields such as data munications, environmental monitoring and security Guard System. We believe that integrated and intelligent Communication Protocols are realized after software design is refined and improved systems to support asymmetric services by using directional antennas.
畢業設計相關推薦
鄂ICP備17016276號-1