qenos焊接工藝規程和維修(編輯修改稿)
2025-03-31 00:05 本頁面
【文章內容簡介】 g the next Inspection interval). ? 凱諾斯焊接檢查員須在所有維修作業完成后，在 SAP中更新 容器 歷史（ 這還包含確定下次檢查間隔）。 23頁 WELDING PROCEDURES AND REPAIRS 焊接工藝規程和維修 ? CURRENT ARRANGEMENTS FOR FIXED EQUIPMENT ? 固定設備的當前安排 ? The vast majority of Fixed Equipment on the various Qenos sites? must be Registered with the respective Regional Government body. ? 在各個凱諾斯場所的絕大多數固定設備必須在相應的地方政府機構處注冊。 ? Alterations and/or Repairs can be performed without additional approval subject to the following conditions being met: ? 滿足下列條件時，更改和 /或維修 作業無須額外 批準 即 可進行： 24頁 WELDING PROCEDURES AND REPAIRS 焊接工藝規程和維修 ? CURRENT ARRANGEMENTS FOR FIXED EQUIPMENT ? 固定設備的當前安排 ? Self Managed Repairs / Alterations ? 自主 管 理 維 修 /更改 ? Like for Like Replacement/s ? 對等更換 ? Weld Repairs associated with corrosion loss ? 與腐蝕損失 關聯 的 焊件維修 ? Additions of same sized nozzles (subject to Code rules related to proximity to other existing nozzles) ? 增加相等大小的管口（需遵循與其他現有管口靠近程度相關的規范法則） 25頁 WELDING PROCEDURES AND REPAIRS 焊接工藝規程和維修 ? CURRENT ARRANGEMENTS FOR FIXED EQUIPMENT ? 固定設備的當前安排 ? Self Managed Repairs / Alterations ? 自主 管理維修 /變更 ? All New, or Repairs to, Existing Piping ? 全新或 維修 現有管道 ? Repairs and/or Modifications to Tanks and other NonRegistered equipment. ? 儲罐 和其他未登記 設備的維修和 /或改動。 26頁 WELDING PROCEDURES AND REPAIRS 焊接工藝規程和維修 ? CURRENT ARRANGEMENTS FOR FIXED EQUIPMENT ? 固定設備的當前安排 ? Major Alterations ? 重大 改動 ? Major Alterations often require that we obtain a New Design Approval from the Regional Government Regulator ? 重大改動往往需要從地方政府監管員得到 新 設計的批準。 ? Following approval, all Welding associated with the Approval must then be fully managed by Qenos. ? 批準后，所有與該批準相關的焊縫須由凱諾斯全面管理 。 27頁 WELDING PROCEDURES AND REPAIRS 焊接工藝規程和維修 ? MODIFICATION TO PIPING ? 管道改動 ? The majority of modification to Piping usually prises: ? 大多數管道改動通常包括： ? New Additions ? 新加 ? Alteration to Existing ? 對現有改造 ? Repairs to Existing ? 對現有維修 28頁 WELDING PROCEDURES AND REPAIRS 焊接工藝規程和維修 ? MODIFICATION TO PIPING ? 管道改動 ? All new Piping fabrication work is done either at the Contractors Workshop or in a Qenos Workshop. ? 所有新管道的制造工作應在承包商車間或凱諾斯車間完成。 ? There is often a number of “tiein” welds that will need to be done in the field ? 經常有很多的“搭接”焊將需要在現場完成。 29頁 WELDING PROCEDURES AND REPAIRS 焊接工藝規程和維修 ? MODIFICATION TO PIPING ? 管道改動 ? Depending upon the Design Code and Service Conditions, either Full, Partial, or No Radiographic Inspection will be required. 哪些管道需要射線檢查，那些不要？ ? 根據設計規范和運行條件的不同，將需要完全、部分 射線探傷或不需要射線探傷。 30頁 WELDING PROCEDURES AND REPAIRS 焊接工藝規程和維修 ? MODIFICATION TO PIPING ? 管道改動 ? All Piping Spools will be subjected to a Hydrostatic Test in accordance with Code requirements. ? 所有管節都需按照規范要求進行一次水壓測試。 ? Tiein welds may be ether “plug hydrotested” (if associated with a flange) or be deemed as a “goldenweld” and only radiographed. 搭接焊縫可進行 “堵管水壓測試”（如果與法蘭關聯） 或被視為“黃金焊縫”并僅進行射線探傷。 ？？ 31頁 WELDING PROCEDURES AND REPAIRS 焊接工藝規程和維修 ? MODIFICATION TO PIPING ? 管道改動 ? Following Inspection and Testing, the pleted pipe spools will be sent off to a Specialist Abrasive Blasting Contractor who will apply the required surface coating. ? 檢查和測試后，完成的管段將被
教學課件相關推薦
鄂ICP備17016276號-1