【文章內容簡介】 爆性能，并符合國家標準GB4208《外殼防護等級的分類》及EPC合同中規定的要求。盤、箱、柜的材質、顏色、厚度等要求必須滿足EPC合同，要求見EPC合同附件，盤、箱、柜的面漆顏色色標要求與廠房內的其他盤柜顏色一致，由買方提供。盤箱柜的防護等級為IP65。 要求給煤機控制柜、接線盒安裝在本體上隨本體一體化供貨，控制柜要求采用不銹鋼制作，控制箱采用堅固的防護裝置防護，防止運輸?shù)跹b過程中變形或損壞，控制箱做為與設計院設計的唯一接口，也就是說賣方配供的接線盒負責將信號全部引至控制箱。控制柜的面漆顏色色標要求與廠房內的其他盤柜顏色一致，由買方提供。要求控制柜下進線，進線孔長方形200（長）100（寬）（mm）。賣方的控制柜接地：柜門與柜體之間接地線連接，綠黃線接地； 給煤機進、出口閘門不在賣方供貨范圍，但連鎖要滿足現場要求。 盤內熔斷器、按鈕、主回路空氣開關、操作用小型斷路器、接觸器、中間繼電器、熱繼電器、限位開關等全部采用進口產品。 接線端子采用鳳凰端子U6K，并留有20%的備用量，柜內接線采用FUN尼龍塑殼線，導線用塑料纏繞管綁扎。并留有DCS控制接口端子。 盤內接線要求：正確、美觀、整齊、標號齊全，安裝接線要求雙重編號：回路編號、安裝接線相對編號。 就地控制柜至就地設備的電纜由賣方提供并接線。電纜選型要滿足EPC合同電纜要求，采用鎧裝。 對于每臺給煤機，買方提供控制箱3 相4 線400/230V 電源。賣方需要其它等級、其它規格的電源時，由賣方自配變壓器自行解決。 賣方在給煤機和其配套部件的安裝使用說明書中專辟章節，詳述其在啟動、停止、正常運行、事故處理過程中的檢測、控制、調節、報警、聯鎖和保護的內容和要求，和配供測控系統的特性、功能、原理、安裝、調試和使用注意事項。賣方在給煤機和其配套部件的安裝使用說明書中，列述其運行中各項參數的正常值、報警值、聯鎖和保護裝置的動作值。 總包合同要求。 賣方提供詳細的控制儀表設備清單。 賣方儀表設備選型必須滿足下表，最終由買方確認。序號名稱制造商備注1熱電阻/熱電偶/就地壓力溫度表上海自動化儀表股份有限公司重慶川儀自動化股份有限公司安徽天康集團有限公司2開關量儀表SOR/UE/ASHCROFT 賣方配供的儀表設備滿足下列EPC合同要求：n Codes and Standards Temperature Measurementa) Instrument and apparatus for temperature measurement ASME PTC (1974)b) Temperature measurement Thermocouples ANSIMC 1982.c) Temperature measurement by electrical resistance thermometers.d) Thermometerelementplatinum resistance. Pressure Measurementa) Instrument and apparatus for pressure measurement ASME PTC (1964)b) Bourdon tube pressure and vacuum gauges. Instrument Switches and Contactsa) Contact rating AC services NEMA ICS Part2 125, A600b) Contact rating DC services NEMA ICS Part2125, N600. Enclosuresa) Types of enclosures NEMA Std. through (Type 4 to 13).b) Racks, panels, and associated equipment EIA: RS310B (ANSI 1972) Cablesa) Thermocouple extension wires/cables ANSI C 1982.b) Colour coding of single or multipair cables ICEA S61 402. (Third edition) NEMA WCS1979.c) Guide for design and installation of cable systems in power generating stations (insulation, jacket materials) IEEE Std. 422 1977. d) Requirements of vertical tray flame test IEEE 383 1974.e) Standard specification for tinned soft or annealed copper wire for electrical purpose ASTM B33 81.f) Oxygen index and temperature index test ASTM D2863.g) Smoke generation test ASTMD2843 and ASTME662.h) Acid gas generation test IEC7541.i) Swedish chimney test SEN 4241475 (F3) Transmittersa) All Transmitters shall be used to provide the required 4to 20mAdc signals for all input to the DDCMIS and other receivers as required. Transmitters shall be of the electronic 2wire type, capable of driving loads up to 550ohms at 24voltsdc. Transmitters shall be furnished with tags to identify service. Local indicator shall be provided for all transmitters.b) All Transmitters shall be smart type with HART Protocol Compatibility, min turndown ratio of 50. Transmitters shall be microprocessor based 2wire type and shall have zero and span adjustments. Transmitter accuracy shall be equal to or better than percent of calibrated span, and the calibrated range of the transmitter shall be in the upper third of its maximum calibration range. The acceptability of each transmitter with respect to range, overpressure capability, and repeatability shall be demonstrated to the Owner. Two interface units shall be provided for each unit. Handheld calibrators shall be provided for calibrating the smart transmitters.c) Field mounted transmitters and analyzers shall be installed in Field Instrument Enclosures (FIE).d) Pressure transmitters shall be equipped with a twovalve manifold, and differential pressure transmitters shall be equipped with a fivevalve manifold. Valve manifolds shall contain instrument, test, and where required, equalizing valves, etc.e) All the Transmitters shall be provided along with local display. n Temperature,Pressure,Level,andFlowSwitchesTemperature, pressure, level, and flow switches shall generally have doublepole, doublethrow (two FormC) contacts for each actuation point and shall be equipped with screw type terminal connections on a terminal block for terminating field wiring. Switch set point shall be adjustable with a calibrated scale to indicate the set point. Contacts shall be of the snapacting type. All switches shall be furnished with individual name tags to identify service. Temperature Switches Temperature switches shall be United Electric Controls. Special length armored capillary tubes shall be furnished where required. Thermowell shall be furnished and shall be as specified in this section. The set point (point of switch actuation) of the temperature switch shall be placed in the middle third of the switches operating range. Each temperature switch shall have an over temperature capability of a minimum of 110percent of the line design temperature. PressureSwitches Pressure switches shall be actuated by disk or diaphragm type elements. Pressure switches shall be selected as follows: General static pressure switches or differential pressure switches for normal medium or high static pressure shall be Static O Ring or acceptable equal. The set point (point of switch actuation) of the pressure switch shall be placed in the middle third of the switches operating range. Each pressure switch shall have an overpressure capability of a minimum of 110percent of the line design pressure for liquid service and a minimum of 150percent for gas service.n LocalIndicators LocalTemperatureIndicators/ GaugesThermometers for local mounting shall be gasactuated thermometers or mercuryinsteel thermometer type. Thermometers for panel mounting shall have stainless steel armoured capillary tubing of the length required for installation with 150 minimum dial size. Dial scales shall be such that the normal operating range