【文章內容簡介】 wser will prompt you to enter the “User name” and “Password: as shown below. 9 One Chunnel GSM Gateway Enter the User name and Password and the press OK to access the GoIP Gateway Web Server. The default for both user name and password is “admin”. Status The Status page shown below is the default / home page of the GoIP Web server. Phone Information A. Serial Number Each Gateway has a unique serial number assigned by the factory such as HT304O12VTEST01. This number is important for centralized configuration, technical support, and warranty. This number is printed on the bottom of the Gateway and is associated with your software license. B. Firmware Version Firmware version identifies the firmware version of the Gateway such as . C. Hardware Mode This field shows terminal’s hardware type. D. Phone Status This field shows the status of Line’s connection status. If the connection is successful, this field displays LOGIN。 otherwise, it displays LOGOUT. Network Information A. LAN Port Configuration This field displays the status of the LAN port. B. PC Port Configuration This field displays the status of the LAN port. C. PPPoE If PPPoE is enabled, it displays its status. D. Default Route 10 One Chunnel GSM Gateway This field displays the IP address of the default routing Gateway. E. DNS Server This field displays the IP address of the Domain Name Server. GSM Module Information A. GSM Module This field displays the GSM module type. B. GSM Signal This field displays the GSM signal type. C. GSM Status This field shows the status of GSM connection status. If the connection is successful, this field displays LOGIN。 otherwise, it displays LOGOUT. Configurations Click on the “Configurations” tab on the left hand column to access the device configuration menu: Preference, Network, Call Settings, Call Divert, Save Changes, and Discard Changes. Click on “Preference” in the left menu of the configuration web, and the screen will be displayed as below: 11 One Chunnel GSM Gateway Language Currently GoIP supports English, Simplified Chinese and Traditional Chinese. Select the language desired and the Web page will be shown in the language selected accordingly. The language can also be selected at the top of the web page. Once selected, the webpage language is refreshed immediately. However, the language selection is not saved until the Save Changes icon is clicked. Time Zone and Time Server The GoIP Gateway supports Network Time Protocol (NTP) to obtain the date and time information from an NTP server (Time Server). The time zone is specified as in GMT 177。 offset. For example, the Pacific Standard Time is GMT8, and the Pacific Daylight Time is GMT7. Note: The GoIP Gateway supports CDR and Billing Information, it is important to set up these two parameters properly. 12 One Chunnel GSM Gateway AutoProvision The GoIP Gateway supports Auto Provisioning which enables configuration parameters to be set automatically without human intervention. The Auto Provisioning supports both HTTP and TFTP protocols. For higher security, encrypted configuration file is also supported. This feature requires external Auto Provisioning Server. Please contact your service provider for further information on this. Network Tone Network Tones are a set of tones used for VoIP calls. Select one of the countries defined or customized to define your own Network Tones. You can configure the Network Tones as Customized option: Each tone listed above is defined in the following format: nc, rpt, c1on, c1off, c2on, c2off, c3on, c3off, f1, f2, f3, f4, p1, p2, p3, p4 Where: nc is the number of cadences rpt is the repeat counter(0 infinite, 1~n repeat 1~n times) c1on is the cadence one on (in milliseconds) c1off is the cadence one off (in milliseconds) c2on is the cadence two on (in milliseconds) c2off is the cadence two off (in milliseconds) c3on is the cadence three on (in milliseconds) 13 One Chunnel GSM Gateway y c3off is the cadence three off (in milliseconds) f1 is the tone 1 frequency (300Hz3000Hz) f2 is the tone 2, frequency (300Hz3000Hz) f3 is the tone 3 frequency (300Hz3000Hz) f4 is the tone 4 (300Hz3000Hz) p1 is the attenuation index for f1, 0~31(0=3dB, 1dB increments) p2 is the attenuation index for f2, 0~31(0=3dB, 1dB increments) p3 is the attenuation index for f3, 0~31(0=3dB, 1dB increments) p4 is the attenuation index for f4, 0~31(0=3dB, 1dB increments) For example, the tone definition for a tone of 450Hz with a cadence of 700 ms on and 1000 ms off is 1,0,700,1000,0,0,0,0,450,0,0,0,20,0,0,0 Call Settings Click on the “Call Settings” to configure the VoIP call settings. The first thing to set is the Endpoint Type: or SIP. Phone For protocol phone, 2 configuration modes are supported: Single Configuration and Configuration by Group. Single Configuration The Single Configuration supports only one VoIP number to a single Gatekeeper.