【正文】 2)蝸桿尺寸 分度圓直徑 d1 d1=28mm 齒頂圓直徑 da1 da1=d1+2ha1=33mm 齒根圓直徑 df1 df1=d1﹣ 2hf=22mm 導程角 ? =176。箱子上面需安裝模壓機下模的支撐裝置，支撐裝置采用螺旋定位。設計中使用了 Auto CAD SolidWorks 等工程制圖軟件。 關鍵詞： 電機線圈 模壓機 蝸輪蝸桿 絲杠傳動 軸 受力分析蘭州交通大學博文學院畢業設計（論文） II Abstract Motor as the power equipment foundation, in recent years to maintain steady and rapid growth in recent years, a number of policy and industrial planning, accelerate the development of the motor to the direction of energy saving. With the development of industrial economy, the motor has been widely used. Manufacturing of motor, using the number of non standard equipment is quite much, non standard equipment required for more. The motor winding molding machine molding equipment is the motor coil for high voltage motor coil production of large and mediumsized ship design. The molding machine molding machine equipment manufacturers has been basically formed, in order to improve the performance of the structure of molding machine and its scope of application, this paper carries on the design to the motor coil molding machine structure, which is applicable to a wider range, more reasonable structure. Design of the main design concept of the bination of the existing premise, in line with the design requirements, design of molding machine bracket angle steel welded structure, two door type steel welding. Molding machine adjusting coil angle through worm, coil width by adjusting screw, can meet most of the needs of production coil. The Auto CAD SolidWorks software is used in the design of Engineering drawing. Keywords: Motor coil Molding machine worm and gear lead screw drive Shaft Force analysis. 蘭州交通大學博文學院畢 業設計（論文） 目 錄 摘要 ................................................................. Ⅰ Abstract ............................................................. Ⅱ 緒論 .................................................................. 1 第一節 大中型高壓電機 .............................................. 1 第一章 電機線圈模壓機的基本結構 ....................................... 3 第一節 電機線圈模壓機的基本結構 .................................... 3 第二章 基本設計計算校核 ............................................... 5 第一節 蝸輪蝸桿的設計計算及其校核 .................................. 5 第二節 絲杠的選型及其計算 ......................................... 10 第三節 軸的設計計算 ............................................... 12 第三章 其他非標準工件的結構設計和材料選取 ........................... 16 第一節 下模設計和材料選取 ......................................... 16 第二節 支撐裝置 ................................................... 17 第四章 solidworks 建模及裝配 .......................................... 18 第一節 下模主體的建模 ............................................. 18 第二節 下模壓板的建模 ............................................. 19 第三節 壓鐵卡的建模 ............................................... 19 第四節 壓鐵的建模 ................................................. 20 第五節 電熱管卡的設計建模 ......................................... 21 第六節 運用 solidworks 的 toolbox .................................. 22 第七節 下模的裝配 ................................................. 24 第八節 箱體的設計建模 ............................................. 24 第九節 箱體的可移動下模支撐建模 ................................... 27 結論 ................................................................. 29 致謝 ................................................................. 30 參考文獻 ............................................................. 31 蘭州交通大學博文學院畢業設計（論文） 1 緒論 第一節 大中型高壓電機 一、 電機的發展歷史 1880 年伏特發明電池，是電氣出現的開端。 （二） 下模：下模是用直徑 200mm，厚度為 10mm 的空心鋼管截出一個 50mm*70mm的截面，兩端為直徑 200mm 的圓形鋼板焊接在鋼管兩端，中心開一個直徑 40mm 的軸孔。 右旋 軸向齒距 Px1=π m= = 齒輪部分長度 b1 b1≥ m(11+ z2)= (11+ 80)= 取 b1=55mm (2)蝸輪尺寸 分度圓直徑 d2 d2=