【正文】 esign level as indicated on the engineering drawing. Prior to initial release (., in the conceptual phases), experimental numbers should be used. 盡可能簡潔地填入被分析項目的功能使之符合設計意圖。 List each potential failure mode associated with the particular item and item function. The assumption is made that the failure could occur but may not necessarily occur. A remended starting point is a review of past thingsgonewrong, concerns, reports, and group brainstorming. Potential failure modes that could occur only under certain operating conditions (., hot, cold, dry, dusty, etc.) and under certain usage conditions (., aboveaverage mileage, rough terrain, city driving only, etc.) should be considered. 典型的失效模式包含下列各項，但不限於此：破碎的、變形、鬆弛、洩漏、黏著、短路、生鏽、氧化、龜裂。 Typical failure effects could be but are not limited to: Noise, Rough, Erratic, Operation, Inoperative, Poor Appearance, Unpleasant Odor, Unstable, Operation Impaired, Intermittent Operation, Thermal Event, Leaks, Regulatory NonCompliance. 設計 FMEA填寫說明 12. 嚴重度 (Severity): 嚴重度是針對失效模式衍生的嚴重影響所作的等級界定乃一相 對的等級評價。 The likelihood of occurrence ranking number has a relative meaning rather than an absolute value. 藉由設計變更或設計過程變更 (如設計查核表、設計審查、設計指南 )才是降低發生率的唯一方法，才是降低發生率的唯一方法 . Preventing or controlling the causes/mechanisms of the failure mode through a design change or design process change (., design checklist, design review, design guide) is the only way a reduction in the occurrence ranking can be effected. 設計 FMEA填寫說明 潛在失效原因 /機制發生率的評估分為 1到 10級，在確定這個估計值時，需考慮下列問題： Estimate the likelihood of occurrence of potential failure causes/mechanism on a 1 to 10 scale. In determining this estimate, question such as the following should be considered: (a) 相似零件、子系統或子系統的過去服務歷史資料和相關經驗 ? What is the service history/field experience with similar ponents, subsystems, or systems? (b) 是否沿用以前使用的零件、子系統或系統 ,還是與其相似 ? Is the ponent a carryover or similar to a previous level ponent, subsystem, or system? (續 )(Occurrence(continued)): 設計 FMEA填寫說明 (c) 與上一版序零件、子系統或系統改變程度的大小 ? How significant are changes from a previous level ponent, subsystem, or system? (d) 零件與上一版序零件 ,更無顯著的差異 ? Is the ponent radically different from a previous level ponent? (e) 零件是否為全新的產品 ? Is the ponent pletely new? (f) 零件的用途是否改變 ? Has the ponent application changed? (g) 作業環境是否改變 ? What are the environmental changes? (續 )(Occurrence(continued)): 設計 FMEA填寫說明 (h) 是否運用工程分析去預估 ,應用此零件之發生度 ? Has an engineering analysis (., reliability) been used to estimate the expected parable occurrence rate for the application? (i) 更無放入預防管制考量 ? Have preventive controls been put in place? 發生率評價等級分?jǐn)?shù)為 FMEA作業範圍內的相對評分，並不 一定反映實際可能的發生 The occurrence ranking number is a relative rating within the scope of the FMEA and may not reflect the actual likelihood of occurrence. (續 )(Occurrence(continued)): 設計 FMEA填寫說明 建議評估標準 (Suggested Evaluation Criteria): 小組成員對評估標準及系統等級應更一致的共識，即使是個別產品分析更所修訂，亦應更一致的共識 The team should agree on an evaluation criteria and ranking system, that is consistent, even if modified for individual product analysis. 註：等級 Note: The ranking value of 1 is reserved for “Remote: Failure is unlikely.” 設計 FMEA填寫說明 建議的 DFMEA發生率評估標準 失效的機率 可能的失效率 等級 極高：失效幾乎不可避免 ≧ 100 每一千輛車 /項目 10 50 每一千輛車 /項目 9 高：一再重複失效 20 每一千輛車 /項目 8 10 每一千輛車 /項目 7 中等：偶爾發生失效 5 每一千輛車 /項目 6 2 每一千輛車 /項目 5 1 每一千輛車 /項目 4 低：相對較少失效 每一千輛車 /項目 3 每一千輛車 /項目 2 極低：不太可能出現失效 ≦ 每一千輛車 /項目 1 Suggested DFMEA Occurrence Evaluation Criteria Probability of Failure Possible Failure Rates Ranking Very high: Persistent failures ≧ 100 per thousand vehicle/items 10 50 per thousand vehicle/items 9 High: Frequent failures 20 per thousand vehicle/items 8 10 per thousand vehicle/items 7 Moderate: Occasional failures 5 per thousand vehicle/items 6 2 per thousand vehicle/items 5 1 per thousand vehicle/items 4 Low: Relatively few failure per thousand vehicle/items 3 per thousand vehicle/items 2 Remote: Failure is unlikely ≦ per thousand vehicle/items 1 (Current Design Controls): 列舉預防、設計確認 /驗證 (DV)或其他已完成或提出的活動，這些 活動將保證該設計對於所考慮的失效模式和 /或原因 /機制是充分 的。 The Design FMEA form in this manual has two columns for the design controls (., separate columns for Prevention Controls and Detection Controls) to assist the team in clearly distinguishing between these two types of design controls. This allows for a quick visual determination that both types of design controls have been considered. 設計 FMEA填寫說明 16. 現行設計管制 (續 )(Current Design Controls(continued)): ※ 在範例中並沒更使用到預防管制欄位 ,因?yàn)樵擃A(yù)防並未被使用在相同或類似的設計上。 It is best to have detection controls in place as early as possible in the design development process. 難檢度應採用表 。 (P預防 ,D檢測 )。 List the prevention, design validation/verification (DV), or other activities that have been pleted or mitted to and that will assure the design adequacy for the failure mode and/or cause/mechanism under consideration. Current controls (., design reviews, fail/safe designs such as a pressure relief valve, mathematical studies, rig/lab testing, feasibility review, prototype tests, road testing, fleet testing) are those that have been or are being used with the same or similar designs. 設計 FMEA填寫說明 (續 )(Current Design Controls(continued)): 小組應隨時均著眼於改進設計管制；例如：於實驗室中創造出系統測試，或創造出系統模型計算程序等。 A reduction in the severity ranking index can be effected only through a design change. 設計 FMEA填寫說明 建議評估標準 (Suggested Evaluation Criteria): 小組成員應對評估標準及等級系統更一致的共識，即使是個別 產品分析更所修訂，亦應更一致的共識。 Typical failure modes could be but are not limited to: Cracked, Deformed, Loosened, Leaking, Sticking, Oxidized, Fractured, Does not transmit, Slip