【正文】 arget and applies it in ESP hardwareinloop test bench, and achieves the CAN telemunication between ECU and sensors.Key words: CAN Bus。主題詞：熱電技術 汽車 應用Introduction of Applications of Thermoelectric Technology in AutomobileJin Peng1, 2 Peng Hui1 Guo Konghui2（ of Michigan。 2. State Key Laboratory of Automobile Dynamic Simulation, Jilin University)【Abstract】Thermoelectric technology, which uses thermoelectric materials to convert thermal energy directly into electricity for power generation, also converts electricity into thermal energy for heating or refrigeration, is an allsolid energy conversion mode, it needs no chemical reaction or fluid medium. The basic principle of thermoelectric technology is introduced in the paper, and application of thermoelectric device in auto tailgas residual heat recovery, reduction of harmful gas emission in tail gas as well as in new auto air conditioning system, are also discussed. The development of thermoelectric technology in China is introduced briefly in the paper.Key words: Thermoelectric technology。 xPC Target。結果表明，重型載貨汽車采用不分離離合器AMT技術，可以在保證換擋平順性的基礎上有效地縮短換擋時間。仿真分析結果表明，在符合法規(guī)要求的前提下，有效減輕了座椅質量。 Ignition system。 meeting the package requirement of thermodynamics. Engine partment of nearly twenty economy passenger cars is studied in the paper, and these principles are explained according to the typical package cases of passenger car engine partment. Key words: Passenger car。 Seizure。 2. Southwestern University of Finance and Economics)【Abstract】 Motion analysis is made to the unitary and double cross universal coupling. The results indicate that phase angle θof the intermediate shaft is one of the factors causing fluctuation of moment at the output end of the driveline. A parameterized model of the double cross universal coupling is established with software Adams/View, with the minimized fluctuation of driven shaft moment as target. Optimized design study is carried out for different design variables and the optimal phase angle and axis hard point package program of the intermediate shaft are obtained.Key words: Double cross universal coupling。以離合器膜片彈簧為例，利用隨機向量描述膜片彈簧尺寸指標，采用MonteCarlo模擬方法，取平均值相同而標準差不同偽隨機向量樣本進行計算分析，研究了采用尺寸向量方差矩陣行列式和方差矩陣跡描述隨機向量離散程度的適用性。 2. Shanghai Diesel Engine Co., Ltd)【Abstract】 With an Euro III diesel engine with electrical control and high pressure mon rail as example, and use ion chromatography to accurately measure sulfate content in PM emission, PM emission and sulfate content are measured and pared to diesel fuel with different sulfur content. The results show that, for heavy duty diesel engine with no catalytic converter, PM emission of diesel fuel with sulfur content approx. 273106 is reduced by % as pared with diesel fuel with sulfur content approx. 800106。 Excessive air coefficient。由于在前期規(guī)劃中進行了焊點可達性分析、機器人仿真分析和干涉檢查等，因而大大縮短了各工位夾具與抓具的設計時間并提高了準確率，顯著減少了后期修改工作量。 2. FAW Mould Manufacturing Co., Ltd)【Abstract】With the welding line planning of vehicle model B of a pany as example, the paper elaborates the application of digital factory technology in BIW welding line advanced planning. The paper introduces BIW welding solution based on digital factory as well as content, flow and implementation of advanced planning. Since welding spot reachability analysis, robot simulation analysis and interference check, etc., are conducted in the advanced planning, therefore the design time of jig and gripper are shortened, accuracy rate is improved, modification work in the later stage is considerably reduced.Key words: BIW。 Performance tes