【正文】 firefighting device。 ? Original scaffold will be used for the painting at height, if not , elevator or ladder will be given instead as well as safety belt. 登 高油漆工作盡量使用原有的腳手架作業，若無腳手架采用升降機或梯子并正確佩戴安全帶。 ? Special care should be taken during unloading of the ready products, no throwing is allowed. 成品件到貨卸車時應輕拿輕放，避免扔擲。 ? Fireproof cloth should be used for protection during welding to avoid being polluted by the falling welding 防護，防止焊渣落到下方成品件上造成污染。 ? Protect the paint around welding seams when perform site welding work with fireproof ，可用防火布覆蓋隔離。成品件進場前 底漆、中間漆、面漆已經完成。 ? The painting site must have good lighting, the temporary wiring shall be safe and reliable and with good ,臨時電器線路架設，要安全可靠，絕緣好。 Painting choosing and ratio: It shall be done as per guideline of manufacturer and manual strictly. Tag number of paint and process of mixing shall be traced by inspector. Control the mixing using life of paint. 油漆的選用及配比：油漆的選用及調配嚴格按照廠家的指導及說明書進行，質檢員需對油漆的牌號及調配過程進行跟蹤，并控制油漆的混合使用壽命。涂漆前用吸塵器，刷子等清理干凈，每層涂膜干燥后 需經同樣處理后，方可涂下一層涂料。 Only grind to the base coat for repairing with Interthane 990 topcoat 。 Surface Preparation 表面處理 Surface preparation before painting 涂漆前的表面處理 ? Surface preparation request: grade. St3, thorough rust removal by hand or power machine or arrive Grade by mechanical rust removal. 表面處理粗糙度要求： St3 級 徹底的手工和動力工具除銹或者采用機械除銹達到 級。然后按照對該部位涂層進行砂磨和清洗，并保證搭接涂層邊緣一定的搭接坡度和新鮮的涂層表面。 record檢查：漆膜測厚儀檢測并記錄 由于涂層厚度超厚，而導致無機硅酸鋅涂層龜裂部位。 Selection of Paint 油漆選用 DC has provided the painting system suitable for this project. The selection of paint shall strictly follow DC construction painting system. Paint type, finish paint color and paint repair color should be chosen in accordance with the line list. The specific painting systems are as follows. 本項目 DC 已經給出了適合本項目的油漆系統，油漆選擇嚴格按照 DC 油漆系統進行選擇施工 。 The safety training and technical training from international pany have been ，進行了安全技術教育和國際公司技術培訓； pipe and fittings shall have qualifications. 管段應具備出廠合格證； Material, tools, apparatus for test and inspection, construction facility and space are ，機具，檢測儀器，施工設施及場地已齊備； Inspection must be done during the course of anticorrosion construction, and perform the acceptance immediately after anticorrosion is ，必須進行中間檢查 ；防腐蝕工程完工后，應立即進行驗收； The coating shall have qualification from its manufacturer 油漆 應有制造廠的質量證明書； Painting environmental condition shall be in accordance with the information on the product sheet. The surface temperature to be dew point relative humidity shall be less than 85%. 涂裝環境條件必須和產品說明書的信息一致。 Tools 主要機具 A、主要施工工具 Description 機具名稱 Wheel Grinding Machine砂輪磨光機 As necessary按需 Manul blasting machine 手動噴砂機 As necessary按需 Internal Grinding Machine 內磨機 As necessary按需 Power Blender 動力攪拌機 As necessary按需 Scraper 刮刀 As necessary按需 File 銼刀 As necessary按需 Wile Brush鋼絲刷 Several 若干 Abrasive Cloth鐵砂布 Several 若干 Paint Bucket 油漆桶 As necessary按需 Brush刷子 As necessary按需 B、 main inspection facility 主要檢測工具 編號NO Name 名稱 Use 用途 Remarks 備注 1 Thermometer 溫度計 Test temperature 檢測溫度 15~50℃ , need to be calibrated termly 需定期校準 2 Sling psychrometer 手搖濕度計 Test temperature and humidity 檢測溫度和 濕度 need to be calibrated termly 需定期校準 3 Dew point calculator 露點計算表 Calculate dew point 計算露點 need to be calibrated termly 需定期校準 4 超生波測厚儀 測量涂層厚度 need to be calibrated termly 需定期校準 5 Holiday tester 漏涂檢測儀 Check holidays of coatings 檢測涂層漏涂點 need to be calibrated termly 需定期校準 6 Replicate tape profile tester 復膜 膠帶法粗糙度檢測儀 Check the anchor profile of substrate 檢測底材表面粗糙度 7 Tape for test cleaning 清潔度測試 膠帶 Cleaning test 檢測清 潔度 8 Flash magnifier 放大器 9 Knife 刀 四、 Painting Process 涂漆 工藝 Local Area Touchup for Piping 管道局部損傷及焊縫修補工藝 確認油漆損傷區域 Confir