【正文】 ：微米 Prime Coat 底漆 Phonolic epoxy intertherm228 環氧酚醛高溫漆 intertherm228 90120 Top Coat 面漆 Phonolic epoxy intertherm228 環氧酚醛高溫漆 intertherm228 90120 Typical Minimum/Maximum DFT Range 典型最小 /最大干膜厚度范圍 180240 Painting System DC204 油漆系統 DC204 steel piping and fabricated equipment under insulation （ 155 to 4000C） Location 部位 DC204 Surface preparation 表面 處理 Abrasive blast cleaning to ISO85011 , (Roughness 4075 microns)噴砂處理至 ISO85011 ，粗糙度達到 Rz=4075 微米 Coating System 涂層配套 Coat Name 涂層名稱 Product Name 產品名稱 DFT: microns干膜 厚度：微米 Prime Coat 底漆 Inanic copolymer intertherm751CSA 冷噴鋁高溫漆 intertherm751CSA 90120 Top Coat 面漆 Inanic copolymer intertherm751CSA 冷噴鋁高溫漆 intertherm751CSA 90120 Typical Minimum/Maximum DFT Range 典型最小 /最大干膜厚度范圍 180240 9 Main Equipment amp。油漆種類、面漆和油漆修補的顏色按照 line list 規定選用，主要有如下種類。再按照修補涂層系統進行修補，涂層修補的其他要求同上節。對于輕微損傷的涂層，不需打磨過深，只需要適度打磨即可進行修補，可直接用 Interthane 990 面漆。 The next painting shall only be done after the last painting finished and dried. 在上一層涂層完成后必須在涂層干硬后經行下道涂層的涂裝?，F(xiàn)場的油漆保護做好有效的控制，才能減少現場油漆的修補。 ? Protect the ready painted products from being polluted by the splashing materials fromg site grinding ，打磨飛濺嚴禁對準成品件以免造成污染。 ? All painters should wear special mask to prevent poisoning. 所有涂裝人員必須佩戴專用的口罩，以防油漆中毒。前一道涂膜實干后，方可涂下一道 漆。通常采用的動力工具，包括鋼絲刷、沖擊工具、砂輪機及砂皮磨光機。 B、 Method of painting repair 涂層修補的方法 For weld seam are or damaged area of coating: Use power sand paper disc to grind the weld seam area or damaged area of coating to Grade St3(damaged coating has been removed entirely ), the pipe welding joint will be treated by manual blasting machine by a level of area and unbroken area shall have a overlapping slope. Overlapping area shall appear new and fresh surface of coating to enlarge bonding force between repair coating and raw coating. Repair position shall be cleaned adequately after preliminary surface treatment, then repair painting as per the whole set of painting repair system and arrive the designed film thickness. For small area, brush painting shall be used. But spray coating shall be used for midcoating and final coating when more coating areas connected together. Brushing style will be taken to the touch up works to ensure the appearance of the coating. 對于焊縫區域或者涂層損壞區域：應用動力砂紙片將焊縫區域和涂層損壞區域打磨處理到 St3 級（被損壞的涂層應完全清除）， 管道焊口采用手持式噴砂機，除銹等級 。 Table of Content 目 錄 一、 Project General Introduction 工程概況 二、 References 編制依據 三、 Preparations 準備工作 四、 Painting Process 涂漆工藝 Confirm the regions that need to repair and repair method 確認油漆損傷部位和修補方法 Surface Preparation Method 表面處理方法 Painting 涂漆 五、 Quality control and Inspection 質量控制及檢查 六、 Safety 安全 七、 Paint Protection 油漆保護 一 二 References 編制依據 三 Preparations 準備工作 The design and other technical document is ready。 Seriously polluted part of coating: Any contamination has already damaged coating (polluted by cement)or the local area where contamination can be removed by easy cleaning. 涂層被嚴重污染的部位：被污染物嚴重污染，污染物已造成涂層損壞（被水泥污染），或污染物已無法通過簡單的清洗就能除去的局部涂層區域。但是動力工具不能除去緊緊附著在管道表面的銹蝕和氧化皮。隔離材料可采用膠帶（小范圍）、彩條布、木板等 . ? The painting surface must be dry. The next paint can be applied only when the last paint film is plete 。 ? Painting in a confined space, it must have a good ventilation and with designated personnel to watch. 在封閉空間內涂漆，必須保證良好的通 風，并有專人監護。 ? Special care should be taken during setting up of the scaffolding to avoid knocking and scratching of the painted parts. Effective anticorrosion mesures should be applied for the scaffolding materials.腳手架搭設過程中特別注意對油漆的保護避免碰撞及摩擦，且腳手架材料已經做好有效防腐。 Paint protection will be performed in three steps: 油漆保護可分為三部分進行跟蹤： First step: trans