【正文】
關于地面加速度的定義中,按要求只添加x軸水平方向的時程分析函數,為了讓結果分析明了,在軟件中還定義了時程結果函數用于數值的圖形輸出,其中包括最高節點的位移變化,二層樓板位置 位移計算結果 地震荷載作用下結構的變形圖 地震荷載作用下最高點的位移變化圖通過軟件分析,結構在地震荷載的作用下沿水平方向位移最明顯,同時我們知道了頂部的位移是最大的,其值為33mm,與實驗記錄的結果很相符但考慮到與實際情況相差不是很大,說明軟件的模擬成果還是非常成功的。與概念設計階段的定性分析也基本吻合,說明軟件模擬的結果是非常理想的。 本色側壓?jiǎn)螌訌?fù)壓竹皮竹材力學性能參考值:10^4MPa,抗拉強度60MPa。具體就落實到柱子截面的選取和優化。再后就是圖三的方案了,這個方案是一個即省料又能保證承荷力的設計。因而方案三的構思自然得到了認可。在布置支撐中我們參照了輸變塔的斜撐布置,如下圖 輸變電線塔、。受到靜荷載和動力荷載,在整體上是受彎模型, 模型的簡化圖 、鐵塊、水箱與振動臺示意柱子可以看成是承受軸心荷載的構件,在不計軸向變形時,柱子的變形主要?dú)w結于受水平地震作用產生附加彎矩使其受彎變形而產生的,因此可以看作是受彎構件,橫梁與樓板變形主要由于承受豎向荷載變形產生,所以,要做到結構剛度與結構質量的優化,必須合理設計梁與柱的結構形式。在結構整體計算階段主要借助有限元分析軟件,對結構整體的剛度有一個初步的定位,為結構選配一定形式的桿件以及結構的優化奠定基礎。 方案優化主要包括方案整體形式的優化與對桿件截面形式的優化,在優化過程中以理論計算為主,并通過實驗對計算結果進行修正,使結構的優化過程有充分的理論與實踐依據。PREFACEThe introduction of this contest illustrates the process of structural design and fabrication through structure concept, optimization, modeling calculation and workmanship, bined with relative documents.The structure form is determined according to petition requests, actual building structure form and material properties so as to reach a simple and clear structure form.Project is optimized from the entire structure form to the selection of the bar section, the optimization process mainly based on theoretical calculations has been adjusted under the loading test results which could provide sufficient theoretical and practical support.Structure calculation consists of procedures of structure simplified calculation, entire structural calculation, structure detail calculation and the structure checking putation. The selection of entire structure form is determined within str