【正文】 no fibre,no Bur,no drawbench。Dimension: Specified dimensions in the drawing are used to check outside shape, function and assembly。4. 模切件邊緣整齊，不得有明顯的纖維和細屑?xì)埩? 裝配時不得有拉絲現象。. 泡棉:圖面尺寸用于檢驗零件外形、功能和裝配。另外一側離型紙廠商出具排版布局圖。 appearance surface shall be plated black Cr on bottom layer and mirror Cr on the surface, the thickness of plate layer shall be 20μm。 unspecified dimensions refer to Pro/e 3D model data。6. 檢測須滿足德信質量標準: 《部品檢驗標準_注塑件》《電鍍件檢測標準》 Product should be satisfied with quality standard of Techfaith Wireless: . 《部品檢驗標準_注塑件》《電鍍件檢測標準》. Electroform: Ni ,T= mm 。穴號應刻在模具上。標有環形圈的是重點尺寸,每批次出貨均需檢查,Qualify時需要做CP/CPK。 Unspecified dimensions refer to Pro/e 3D model data。 and transportation: appearance surface shall be protected by film(3M 3K04), Product should be packaged independent, and lay in tray, finally put the trays in the paper box。 unspecified dimensions refer to Pro/e 3D model data。7. 產品采用多單層疊合結構，彎折工作區壽命要求達到10萬次以上； Product should be constructed by singlesided layers . Flex fatigue life of the folding area must rech to 100,000 times。 外觀皮紋: VDI 27. Surfaces texture:VDI 276. 檢測須滿足德信質量標準:《部品檢驗標準_注塑件》 Product should be satisfied with products quality standard of plastic: 7. 包裝:夾鏈袋包裝,注明袋內數量. Packages: packaged by bag with fastener,label quantity. 11. FPCBA1. 圖面尺寸用于檢驗零件外形、功能和裝配。5. 產品外觀： 分型線段差≤,所有圓角和脫模斜度按照Pro/e 3D Data。 Height of injection gate remained in the product should be lower 。：邊及分型線段差≤。 未注尺寸依照Pro/e 3D Data，,未注脫模斜度1度。 The tolerances of the outline and the dome39。 Tolerance: Unspecified tolerance should ply with tolerance table in the drawing產品采用氣槽結構。：見圖； drawing of F/S: see this F/S drawing。:毛刺≤, 為沖切毛刺方向，成品清潔、無雜質、無劃傷及其它瑕疵。s resistance shall be less than 。:毛刺≤, 為沖切毛刺方向，成品清潔、無雜質、無劃傷及其它瑕疵。 : SUS304(stainless steel), T=,。 Unspecified dimensions refer to Pro/e 3D model data。 Appearance:The burr , step of partline : ≤ Product should be tidy and purity, no nick, no shrinkage and other blemish。 Specified dimensions with marked ring are critical dimensions, need to be checked every shipment, and must do CP/CPK check in the qualification stage.：未注公差依照?qǐng)D面公差表。 Material: SANTOPRENE 20164, hardness: 64177。 Print area shoudle be uniformity, no nick , no flaws. 3)印刷字體及顏色請參照右下腳表。 surface of product should be protected with static film. 1檢測須滿足德信質量標準： Product should be satisfied with quality standard of Techfaith Wireless: 1)《》 2)《》 . LENS(CNC)1. 圖面尺寸用于檢驗零件外形、功能和裝配， 未注尺寸請參考3D Pro/Engineer 零件圖。 Draft angle should be less than 1%%d, unless otherwise specified. Unspecified round: ?！禛B_T18287_2000蜂窩電話用鋰離子電池總規范》. LENS(注塑) 技術要求：1. 圖面尺寸用于檢驗零件外形、功能和裝配， 未注尺寸請參考3D Pro/Engineer 零件圖。 Salt fog test: In35161。，前后殼配合周邊嚴禁溢料。 Specified dimensions in the drawing are used to check PCB outside shape, function and assembly。 (Shielding) Shielding is allowable is this limiting height for the ponents with shielding； (No Shielding)Shielding is allowable is this limiting height for the ponents without shielding；2. 器件準確位置以文件中的 直角頂點為準。外觀皮紋：拋光：Product should be tidy and purity, no nick, no shrinkage and other blemish。 Unspecified draft angle: 1176。 Galling should be less than 。 Tolerance: Unspecified tolerance should ply with tolerance table in the drawing。 Material: POM Dupont500,use 100% raw material .2. 尺寸: 圖面尺寸用于檢驗零件外形、功能和裝配。 Unspecified draft angle: 1%%d。 穴號應刻在模具上，標志不得高于表面。 ,未注脫模斜度1度, 未注尺寸依照Pro/e 3D Data。飛邊及分型線段差≤,頂桿痕≤。返回索引目錄 (Shielding) 指可以放置屏蔽罩區域。pad should be located inside the the outline of limited area。4. 產品檢驗標準：； Product should be satisfied with quality standard of Techfaith Wireless: ；： 產品按一定數量密封包裝，需防污防潮。Dimension: Specified dimensions in the drawing are used to check outside shape, function and assembly。 Electric function refer to: 《Li+BATTERY SPEC》：電池用塑料袋和紙盒獨立包裝。Unspecified dimension tolerance should ply with the general tolerance table in drawing.4. 材料： 材料采用 PMMA 三菱VRL40 ,顏色為無色透明,注塑時須采用100%原材料。 Transparency ratio: 91%.正面噴涂UV,UV漆表面硬度≥3H,1kgf Hardness of surface should be more than 3H,1kgf after UV coating.8. 耐磨:RCA 300 cycles； Wearable : RCA 300 cycles；9. 附著力:百格實驗，脫落面積≤3%，并沒有整格脫落； The ply adhesion of printing ink : ≤3% ,no hwale pane desquamate.10. 模具要求： Tooling requirement: 產品區域無頂桿痕. No mark of injection pin. 澆口位置需與設計者商定； Locations of gate should be determined by arrangements. 外觀為鏡面。 Unspecified dimension tolerance should ply with the general tolerance table in drawing.4. 材料：材料采用 PMMA 三菱NR200板材 ,顏色為無色透明。 1檢測須滿足德信質量標準： Product should be satisfied with quality standard of Techfaith Wireless: 1)《》 2)《》06. Audio_cover amp。 Unspecified round: 。澆口凸出≤。返回索引目錄5. 包裝與運輸：采用夾鏈袋包裝，注明袋內數量。 重點尺寸:標有環形圈。 unspecified dimensions refer to Pro/e 3D model data。 and transportation: Product should be packaged independent, and lay in tray, finally put the trays in the paper box。 unspecified dimensions refer to Pro/e 3D model data。 and transportation: put shieling in SMT band ,Don39。重點尺寸:標有環形圈。15％ Φ4( test surface)，material：SUS301 operation force OF:160+/30g click ratio :45%177。3SHA，用100%原材料。 Unspecified dimensions refer to Pro/e 3D model data。 外觀皮紋: VDI 21。2. 重點尺寸:標有環形圈。 Ejector pin marking should be lower mm than surfaces。5. 產品外觀/Product appearance: 成品表面清潔，產品邊緣切割整齊無毛邊； Product should be tidy , no nick and burr。 未注尺寸依照Pro/e 3D Data。：毛刺≤,成品清潔、無雜質、無劃傷及其它瑕疵。 未注尺寸依照Pro/e 3D Data。 Appearance：Stamping burr shall be less than mm