【正文】 N 采用抽芽孔以螺絲固定FDD 抽芽破裂 裝配不良 7 抽芽過高 7 治具 2 98 降低高度 OK 降低高度 7 2 2 28 材質不良 3 無 4 84 更換材質 OK 更換材質 7 1 4 28 FMEA在 FOXCONN 制程名稱 /目的 預估失效模式 預估失效影響 嚴重度S 預估失效原因 發生率O 現行控制措施 難檢度D RPN 建議控制措施 責任人 完成日期 狀態 已採取之措施 S O D RPN 裝上蓋 卡鉤卡不到位 影響外觀和功能 6 人工操作 3 無 6 108 使用夾具 OK 使用夾具和增加檢驗工站 6 2 2 24 裝FDD FDD錯位 FDD磁片彈不出 8 人工操作 3 無 8 192 使用夾具 OK 使用夾具和增加檢驗工站 8 2 1 16 FMEA在 FOXCONN ActionTakenS O D RPNDate (rev.)QE Responsible:Tool Responsible: PageData(Orig.):REV: Severity of failure effect: 1=minor/noeffect 10 = veryhigh/hazardous Occurrence of failure cause:1 = roomette/unlikely 10 =veryhigh/almost inevitableFMEA Leader: Detection of failure cause: 1 = very high/almost certainly 10 =very low/unlikely Risk Priority Number (RPN) = Severity(S) * Occurrence(O) *Detection(D)PotentialCause(s) ofFailurePROCESS FMEAProcess Name: FMEA Team: Ranking guidelines: Document No:ProductRequirementPotentialFailureModePotentialEffect ofFailureS OCurrentProcessControl(s)D RPNAction ResultsRemendedAction(s)ResponsiblePersonCompletionDateStatusFMEA在 FOXCONN FMEA的作業范例 : ? 以 NOKIA產品舉例說明 ? ? ? ? ActionTakenS O D RPN. . 外觀不良.6操作不當,治具不能保護產品的外觀. acover及window不良.包裝不良6work carefully,operator 100%selfcheck, IPQC check, traceback/ PDCS.3 108 2023/4/20 OK trained 6 4 3 72. 外觀不良.5熔接參數不當,如:機臺壓力,速度,熔接時間及凝固時間.3operator 100% selfcheck, IPQCcheck, traceback/,速度,熔接及凝固時間.2 30 OKSOPCMKA00045 3 2 30. 功能不良.8熔接參數不當,如:機臺壓力,速度,熔接時間及凝固時間.2 gauge (9W009U02G1)spec:Fmin=100N, V=10mm/min.,速度,熔接時間及凝固時間.3 48 OKSOPCMKA00048 2 3 48 功能不良造成產品段差7治具不當,熔接參數不當5治具維護,控制機臺壓力,速度,熔接時間3 105 2023/4/28 OKSOPCMKA00047 2 3 42RPN增加定位治具,加強檢驗使用GoNoGo (9W009U03G1)Action Results使用軟質材料做治具,培訓,型按CMKM0015.RemendedAction(s)ResponsiblePersonCompletionDateStatusProductRequirementPotentialFailure ModePotential Effect ofFailureSPROCESS FMEAProcess Name:acover assemblyFMEA Team: Ranking guidelines: Document No:CQKO0001: 2U009001FMEA Leader:Yonghui Ning Detection of failure cause:1 = very high/almost certainly 10 = verylow/unlikely Risk Priority Number (RPN) = Severity(S) * Occurrence(O) *Detection(D)PotentialCause(s) ofFailureOCurrent ProcessControl(s)DData(Orig.): 2023/12/25 REV:A Severity of failure effect:1=minor/noeffect 10 = very high/hazardous Occurrence of failure cause:1 = roomette/unlikely 10 =very high/almostinevitableDate (rev.):2023/04/25QEResponsible: ToolResponsible: Page: 1 of 1FMEA的作業范例 : ActionTakenS O D RPN灰塵. 外觀不良.6..7.,供應商品質改善(VDCS)3 126 2023/4/16 OKSOPCMKA00046 4 3 72氣泡. 外觀不良.6..5 100% selfcheck, IPQC check,traceback/PDCS.3 90 2023/4/16 OKSOPCMKA00046 2 3 36c. 保護膜劃傷. 外觀不良.6..7operator 100% selfcheck, IPQC check,traceback/PDCS.4 168 2023/4/16 OKSOPCMKA00046 4 4 96位. 外觀不良.6.5 ,供應商品質改善(VDCS) check, traceback / PDCS.3 90 2023/4/16 OKSOPCMKA00046 2 3 36Date (rev.):2023/04/25QEResponsible: ToolResponsible: Page: 1 of 1 Risk Priority Number (RPN) = Severity(S) * Occurrence(O) *Detection(D)Data(Orig.): 2023/12/25 REV:A Severity of failure effect:1=minor/noeffect 10 = veryhigh/hazardous Occurrence of failure cause:1 = roomette/unlikely 10 =veryhigh/almost inevitablePotentialCause(s) ofFailureOCurrent ProcessControl(s)D: 2U009001FMEA Leader:Yonghui Ning Detection of failure cause:1 = very high/almost certainly 10 = verylow/unlikelyPROCESS FMEAProcess Name:acover assemblyFMEA Team: