模具英語大匯集-wenkub
2023-04-19 01:16:55 本頁面
【正文】 ess 沉頭螺絲 hex screws 斜坊 set screw盤旋的 guide strip紅外線接受器 synthetic resin大水口系統 infraredtransmitter下頂針板 pin point gate system間隔板 ejector retainer plate 活動板,推料板 core plate A bolster plate(holder material) 拉桿定位。 俯視圖 front view 側視圖 plane view 平面圖 contour挖槽 flow line多重曲面 filter 橢圓 polar多邊形 isometric雙向 one way圓滑曲線 blend導針。拉桿。水口邊定位介子 tapped hold for eyebolt熱膨脹系數 welding rod氣槍 spiral hose磨坊。 鑽頭。 磨擦。 轉動。適配模板 leader pin。帶肩導針( 實心) angle pin(horn pin)啤把鎖 bronze plated bushing導向?qū)?togglelock early ejector return 加速頂棍 accelerated ejector 可折疊式的型芯 slide retainer快速拉桿鎖定裝置 tapped hole 非復位注射計數器 profiled ejector pin 紅銅 brass 青銅 BeCu 拔頭,介子托 fan gate 圓形入口 pin point gate 入喉箍 jiggle 英制螺絲(粗牙) British Standard Fine Thread BSF 美制螺牙 pressure plug 壓力彈簧 vent 斜鎖 ball catch 水口鐵 Jiffymatic connector扁頂要管定,以防旋轉. ejector bearing length加強筋 steel pad拉桿 sprue puller insert頂棍 ejector retainer plate 下頂針板 stripper plate脫料板 P/L flash拖花 burn碼板 side gate system簡化型細水口系統 pin point gate system直邊/托司 top clamp plate推板 spacer block底板 shoulder guide pin托司 straight guide bush直邊 screw thread空氣泵 alloy 合金鋼 定模座塊top plate 動模座塊bottom plate 上模座塊lower clamping plate 凹模固定板coreretainer plate 突模固定板chase。backing plate。parallel 支架angle pin,finger cam 滑塊side core slide 滑塊導板heel block,wedge bock 斜槽導板dogleg cam 斜滑塊 導向零件guide pillar。ejector guide pillar。guide bushing 推板導套length bolt。 limit plate 推流道板runner puller。sprue puller 鉤形拉料桿sprue puller,ballheaded 圓錐頭拉料桿ejector tie rod 推板mouldshut height 抽芯距corepulling force 脫模力mould opening force 模內壓力 lifting clamps 小五金工具h(yuǎn)igh pressure hose 風管,水軟管pressure gauge 壓力油喉photoelastic testing 吹塑模plastic injection mould 沖扎復合模mismatch。witness line枕位 venting valves疏氣塞 valve casing旋鑽 harden/nitride退火 temper應力斷裂 corrosion resistance物】抗張強度,抗拉強度 split mould斜面 inclined bolt (工具,機械等)夾住東西的部分,鉗口 step change of the P/L較薄的料位 cleanup模具日志鑲件 Hot Sprue Bushing半自動 quick disconnector足量注射 mismatchlifting hole平行塊 piston柱塞 carrier支架 item number商品目錄編碼 dimensional datum淬硬証明文件 backup bushing起重螺絲,千斤頂 tapped hole成對角的角落 burn mark(熱流道板)分流板 texuring(注塑機)碼模螺絲 imperial公制的 puller bushing水口鐵 drool bushing限位制 water line connected internally or hard tubing用方形柱或用管釘防止斜頂轉動 gate insert流道開關配件 guided ejection前后模接觸面 waterlines clear tie bars.平衡入水值 spacer挖槽 rough精加工 plunge rate提刀速率 splindle rate冷卻液 SPLIT RINGside pullingcore force 邊針 Tee slot cutter雙向切削 constant overlap spiral環繞切削 parallel spiral clean corners依外形環繞 true spiral單向 end mill球刀 bull mill面銑刀 rad mill倒角刀 slot mill推拔銑刀 dove mill棒狀 drill紋刀 bore bar右牙刀 Tap LH中心鑽 spot drill沉頭孔刀 c. sink舉升曲面 coons surface直紋曲面 revolved surface掃描曲面 draft surface磨砂使用的輪子 quench steel應力消除 molten氧化層 guide pin and sleeve, locating ring ,ejector ,ejector balde, ejector sleeve,lifters, wear plate,horn pin,O
外語相關推薦
鄂ICP備17016276號-1