選購指南-氣缸油缸氣控系統液壓系統包裝機械大梁校正儀大梁-wenkub
2023-04-17 00:19:31 本頁面
【正文】 ylinderCK3X2CK3X1CK3XCK3V1CK3B高CK3B低CK3TLZEMΦ32Φ40Φ100Φ100100Φ125F200QGBIIKΦ32Φ40Φ100Φ125QGBIIKFΦ32Φ40Φ100Φ125QGBIIZKΦ32Φ40Φ100Φ125LGKΦ32Φ40Φ100Φ125LGKFΦ32Φ40Φ100QMKΦ20Φ40DQGIKΦ12Φ25Φ32Φ100LTAIKΦ25Φ100工作電壓 work voltageAC：24220V DC：24220V工作電流 work electric current0300mA壽命 life大于1000000次/More than 1000000 times安裝方式 installing type固定卡式Fixing card type綁帶式 Bandage type固定卡式Fixing card type固定卡式Fixing card typeThe magnetism switch usage regulation1. The voltage and electric currents should avoid exceeding the scope of application.2. Strictly forbid the magnetism switch and power supplies to connect directly, be sure to (such as relay) use with the load.3. Before using the magnetism switch, confirm the working power. If adopting the D. C. source, the red line of the magnetism switch connects to the positive pole.4. Please avoid using in the strong magnetic field and the environment of the big electric current, if using, please add the shield assembly.5. Choose the accessories: according to the action and the request of connecting.Part two: The choice of the valve 一、Choose the valve type1. Choose the electric valves in the situation of autocontrol, remote control and plex control.2. Choose manual valve or pilot foot valve if operated expediently.3. In the situation of mechanical controlled reversing，choose the mechanical controlled valve.4. In the flammable, explosive and wet situation, you’d better choose the pneumatic control valve二、Choose the aperture of the valveBased on the difference of the types of the actuator and the using field and occasion, choose the right valve type. Using 4 or 5 port valve to control the double acting function air cylinder, using three port valve to control the singlerole air cylinder, and using the two or three port valve to control the flowing conversion.The pneumatic technology is working with pressed air for energy and signal transmission, and it uses pressed air to store energy and to drive the working part (such as air cylinder). For the gas flow is quick, so the air cylinder can receive highspeed linear or rotary movement. In normal circumstances, the largest speed of the piston can reach up to 1m/s, but actually we used to choose the best speed (50500mm/s) rather than the maximum speed, the best speed is the most economical. By contrary, worked at the situation of maximum speed not only intensified abrasion and reduced the service life of air cylinders and connecting pieces, but also increased energy consumption. The following table is the remendation of choosing the reversal valve and the air cylinder.Bore101620253240506380100125160200250320400Valve’saperture4***6*****8****10****12***15****20***25***三、The other information of choosing the valve 1. The air port is marked by letters, the following is the corresponding function: A, B Working port or Output port (connecting to the actuator) P Inlet port (connecting to the pressed air) R1(O1)。10. 要定期向中間擺動軸或尾座軸聯接的安裝件加注潤滑油。7. 電磁閥安裝使用時，要注意電磁頭的控制電壓（AC220V AC110V AC36V DC24V DC12V），允許電壓波動1510%。3. 通?；钊麠U只能承受軸向載荷，安裝時要保持負載與活塞桿的軸線一致，如果行程較長，活塞桿應加適當?shù)闹?，防止活塞桿的下垂和彎曲。6. 油霧器一旦逆流，會造成內部零件損壞和發生危險，故應避免發生。2. 空氣過濾器的過濾精度有5mm，10mm，25mm，50mm，75mm五種，可根據空氣的質量要求選用合適的產品，無特殊情況，推薦選用25mm。推薦換向閥與氣缸的選配如下表所示：氣缸內徑Bore101620253240506380100125160200250320400換向閥通徑Valve’saperture4***6*****8****10*
環評公示相關推薦
鄂ICP備17016276號-1