【正文】 ocess and the introduction, the first in China to C8812E mobile phone back cover design, determine the parting surface, gating system design, the choice of injection molding machine, and then to Pro/ selection of die set, check, etc., these processes are very detailed the cell phone back cover injection mold design process mainly USES the Peo/ modelling design and its related to mobile phone shell EMX die fast on the selection of die gating system using Moldeflow software mainly gate location optimization, cooling circuit optimization, injection pressure, and a series of auxiliary analysis, through these analysis can be design to improve design, a very large extent, save the design cycle, improve the this design, not only for injection mold design had a deeper understanding, also make learning knowledge was obtained. Keywords: injection mold, Pro/E, simulation processing， Moldflow 基于 Pro/E 的手機外殼模具設計與解析 3 目錄 摘 要 ..................................................................................................................... 1 Abstract..................................................................................................................... 2 1 前言 ..................................................................................................................... 1 模具工業在國內外現狀及其重要性 ................................................................ 1 設計的目的及意義 ........................................................................................... 2 2 塑件成形工藝性分析 .......................................................................................... 4 手機后蓋分析 .................................................................................................. 4 塑件的材料性能 .............................................................................................. 5 塑件的工藝性能 .............................................................................................. 5 3 注塑機的確定 ..................................................................................................... 6 分型面的確定 .................................................................................................. 6 型腔的數量確定及排列方式 ........................................................................... 6 注塑機 的選擇 .................................................................................................. 8 4 澆注系統的設計 ................................................................................................ 10 澆注系統的組成和設計原則 ......................................................................... 10 主流道的設計 ................................................................................................ 10 分流道的設計 ................................................................................................ 11 澆口的設計 .................................................................................................... 12 排氣方式設計 ................................................................................................ 13 型腔、型芯的結構設計和固定方式 .............................................................. 14 型腔、型芯工作尺寸計算 ............................................................................. 14 型腔側壁和底板厚度計算 ............................................................................. 15 動模墊板厚度 ................................................................................................ 16 基于 Pro/E 的手機外殼模具設計與解析 4 5 脫膜機構的設計 ................................................................................................ 17 推出機構 ........................................................................................................ 17 分型原理 ........................................................................................................ 17 脫膜力計算 .................................................................................................... 17 推桿尺寸計算 ................................................................................................ 18 合模導向機構設計 ......................................................................................... 18 定位圈的設計 ................................................................................................ 18 復位機構設計 ................................................................................................ 19 冷卻系統的設計 ............................................................................................ 19 6 校核 ................................................................................................................... 21 注射壓力機的校核 ......................................................................................... 21 鎖模力的校核 ................................................................