【正文】 遼寧科技大學本科生畢業設計 （論文） 第 I 頁斜刀片冷剪機設計遼寧科技大學本科生畢業設計 （論文） 第 II 頁摘要本次設計的目的是能夠綜合的運用所學的知識，理論，對斜刀片冷剪機進行設計。首先介紹了了我國當前的剪切機的種類，今后的發展方向，提出剪切機在生產中存在的問題；然后對斜刀片冷剪機的傳動系統進行分析，提出設計方案，最后對剪切機構的主要零件進行受力分析和強度校核。分別對齒輪的選擇，軸的選擇，還有軸承和皮帶輪的選擇進行了設計計算，以此同時也進行了校核。對齒輪進行設計的時，我采用的是對齒輪齒面接觸疲勞強度進行了計算，并且運用齒根彎曲疲勞強度進行了校核。在校核過程中，對齒輪的設計校核有了更深的認識，以及如何在剪切機中選用合適的齒輪。并對剪切機中的主要零部件的潤滑方式進行了論述，運用 ATUOCAD 軟件，對該設計的可靠性與經濟性進行分析評價。關鍵詞：斜刀片剪切機；ATUOCAD 軟件；設計；校核Design of cold shear blades obliqueAbstract遼寧科技大學本科生畢業設計 （論文） 第 III 頁This is designed to prehensive use of knowledge, theory, the blade cut machine design cold. It introduces the present situation of our country39。s shear machine type, the future direction of development, put forward the shear machine in production problems。 And then the blade of the transmission system of cold cut machine, the article analyzes the design scheme, then to the main parts of shearing mechanism analysis of stress and intensity. On the choice of gear respectively, the choice of the shaft bearing and pulley, and the selection of design calculation, and, in doing so, also checks. The design of gear, I use is on gear tooth surface contact fatigue strength calculation, and use the tooth root bending fatigue strength checks. In checking process, the design of gear check had a deeper understanding, and how to choose the right in shear machine of the gear. And the shear machine of main ponents of lubrication method were discussed, use ATUOCAD software, to the design reliability and economical analysis and evaluation. Keywords: Inclined blade cutting machine 。 ATUOCAD software ；design。 checked.目錄摘要…………………………………………………………………………….Ⅰ遼寧科技大學本科生畢業設計 （論文） 第 IV 頁Abstract………………………………………………………………………..Ⅱ1 緒論 ..............................................................................................................1 剪切機的種類 ..................................................................................................................1 平行刃剪切機 ....................................................................................................1 斜刃剪切機 ........................................................................................................1 圓盤式剪切機 ....................................................................................................2 沖型剪切機 ........................................................................................................3 聯合剪切機 ........................................................................................................3 型材棒料剪切機 ................................................................................................3 剪切生產中存在的問題 ...........................................................................................42 傳動方案的選擇 ..........................................................................................6 皮帶傳動的選擇 ...............................................................................................................6 減速器傳動選擇 ...............................................................................................................6 齒輪轉動選擇 ...................................................................................................................7 ...................................................................................8 設計的基本要求 ...............................................................................................................8 剪切機構 ...........................................................................................................................8 主要參數的確定 ...............................................................................................................9 刀片的行程.................................................................................................................9 刀片尺寸.................................................................................................................10 理論空行程次數.....................................................................................................10 剪切力的計算 .................................................................................................................10 單位剪切阻力曲線.................................................................................................10 最大剪切力.............................................................................................................11 電機容量的選擇 .............................................................................................................13 = f(α)曲線繪制 ......................................................................................................13=f(α)曲線的繪制 .....................................................................................................13 偏心軸上的靜力矩計算...........................................................................................13遼寧科技大學本科生畢業設計 （論文） 第 V 頁4 主要零件的強度計算 ......................................................................................19 曲軸的設計 .....................................................................................................................19 曲軸的計算 .....................................................................................................................20 齒輪的計算與校核 .........................................................................................................21 選定齒輪類型，精度等級，材料及齒數...............................................................21 設計計算齒面接觸接觸強度 ......................................................................................22........................................................................................................22.................................................................................................................22 按彎曲疲勞強度進行較核設計...........................