【正文】 MTL/ SGS TEST LIST (1) (Seating) (Combines Adult and Children’s sizes,:Chairs, Barstools, Ottomans,) Quality test standard/method Criteria（標準） Results / Design/Features（標簽 /設計特點） The actuality must keep consistency（一致性） with the claim（要求） . 指示 說明 Shall be included if necessary. Shall include assembly, mounting（裝備） , use, maintenance（維護） , cleaning and safety information as required in the language(s) applicable to the destination（目的地） country(s) with no errors or spelling mistakes.（ 地名寫錯） Shall be easy to follow and accurate. size/weight 產品尺寸 重量 Report actual. Shall ply with any claims (0%, +3%) 4. Costco Plastic Bag Warning Statement If plastic bags (of any thickness) with a perimeter(周長 ) of 14 inches or greater are used in inner packaging, the following warning statement must be printed on at least one side of each bag in English, French and Spanish: 5. Lead In Surface Coating（被復蓋） Shall not exceed 600 ppm (% by weight) total lead 6. Workmanship（工藝） / Level ? No major defects（缺點）。 ? No ponents（成分） missing, malformed（畸形的） or fractured （破裂） ? No hardware missing ? Smoothly ground welds（接合） , not overground and free of pits（凹陷） and splatter（說話結巴） ? No burrs（喉音） ? No loose ponents and unsecured fastening where rigidity（硬 度） is required ? In the case of wood (. laminates（薄板 ) proper and uniform（一致的） adhesion（支撐） ? No scratches, dents（凹痕） , cracks（裂縫） , marred（損壞） or discolored surface ? In the case of molded plastic, consistent and concise form and no defects evidencing（明顯的） of overuse（過度的） of mold。 ? Finished edges and seams（銜接口） ? Accurate and consistent（調和的） painting ? Components even in color, uniform clarity ? All seams and ponents in even alignment（結盟） ? Accurate and consistent painting ? Components even in color, uniform clarity（清楚） 7. Sharp Points and Edges Shall have no sharp edges or sharp points on any ponent other than those required for functional use. 8. Cross Cut Adhesion Plating / finish must stay affixed – using a utility（萬能） knife, cut a grid of 16 squares. Use 3M masking tape (202), apply to the grid. Remove to see if plating / finish remains intact.（完整無缺） 9. Flammability（可燃性） of Upholstery Must ply with California Bureau of Home Furnishings Bulletin Materials 116/117 10. Finger Entrapment Shall meet the requirements intended to eliminate （消除） the possible hazard （危險） that may be caused by changing clearances or permanent（永久的） entrapment and pinching（收宿） of fixed openings.(5mm or 13mm) 11. Resistance To Hot Water Pour 25 mL. of boiling water and allow cooling. Dry surface, Shall be no graying（灰色） or spotting（斑點） 11 Effects Of Extreme Temperature 24 Hours At 32176。 F And 140176。F No failure 12. Resistance（抵抗力） To Corrosion（侵蝕） (Metal Components) Shall withstand（抵擋） 24 hours in 1% salt spray (fog) with no corrosion or visual change. 13. Effects Of Humidity（濕度） No change after 24 hours. @ 95% RH amp。 100176。F 14. Stain（污點） Resistance (Do not test on piic table/ benches/ racks) Various food materials – should resist permanent staining.( After 2 hours, remove) 1. French’s Mustard t/2. Heinz Ketchup/3. Ragu Spaghetti sauce (original)/ 4. Folgers Instant Coffee/ 5. Welch’s Grape Juice/6. Kraft BBQ Sauce (original) / Red Wine 15 Resistance to Scratching / Marring Other Surfaces No scratching or marring of surface (3 cycles of 6” back and forth.) Conduct with and without levelers. Note if levelers bee bent or e off. Note any damage / defects (bent/broken levelers) 16. Caster Performance (If Supplied) Max 5 lb pull to move under 200 lb load 17. Rear Stability 背后的穩定性 Min 35 Lbs. (30 Lbs. children) tipping force with a 173 Lbs. (100 Lbs. children) weight placed on the seat (Strap). Force is applied in rearward direction against 1inch obstruction. Report result when seat is in minimum, midpoint and maximum position 18. Front Stability (Excludes（把 … 除外） Barstools amp。 Ottomans) The chair is obstructed（阻塞） by 1 inch bar in the front base, tipping force is measured in the 45176。 to the test platform. The tipping force shall not be less than 40% of the total chair weight. 19. Tip Resistance (Stools Only) Min 10 degree with 150 Lbs. (Children 100 Lbs.) distributed load, no tipover 20. Stability (Stools Only) Min 20 Lbs. pull force after 150 Lbs. (Children 100 Lbs.) distributed load on the seat, no tipover 21. Base Durability（耐用力） No structural（結構的） failure or permanent（永久的） deformation（變形） under 400 Lbs. (225 Lbs. children) static （靜力的） load for 60 minutes. For multi seatback positions, report result when seat back is in minimum, midpoint, and maximum positions for 20 minutes each. 22. Front Seating Capability (Excludes Barstools amp。 Ottomans) No failure under 300 Lbs. (135 Lbs. children) loading at edge (6 In.) 23. Impact（碰撞） Durability (*If applicable – perform with and without cushion（墊子） ) No structural breakage, max 188。 inch deformation（變形） when 225 Lbs. (200 Lbs. folding chairs, 175 Lbs ottomans, 100 Lbs. children) test load free falls from 6 inch to the center of the seat. For multi seatback positions, report result when seat back is in minimum, midpoint, and maximum positions. If chair has levelers, conduct test with levelers fully extended then rotated（旋轉） inward （向內的） two revolutions. 24. Back Pull Durability 后拉力 耐久力 No failure at 100 Lbs. (60 Lbs. children) for 1 min. applied（應用） to 90176。 from back at 16 inch above the seat. 25. Arm Strength Test (Vertical 垂直的 ) No permanent deformation at 300 Lbs. (90 Lbs. children) for 1 min. The vertical（吹垂直的） load is uniformly（均一的） applied through a 5 inch wide board across both arms – No failure / deformation 26． Arm Strength Test (Horizontal 水平的 ) No permanent de