【正文】 進行調整。 Make sure all card ponents shall be pulled from plug. And then switch on main power switch of cabi, power unit, power ponents. Applying voltage meter to measure direct output voltage, the measuring results shall be pliance with manufacture instruction. ( 177。 ,12 177。 , 12 177。,24+). Adjusting if out of deviation allowance. 3) 進行雙電源手動切換試驗 Executing manual switch test with double power supply. 4) 將各嵌套扇、信號變換器風扇、硬盤驅動器風扇、柜頂、門風扇等電源接通，檢查各風扇，應運行正常。 Running all ferrule fans, signal conrertor fans , hardpand—driving fans,top cabi, door—fans, and checking whether they are normal or not. 5) 檢查電源報警電路是否起作用。 Checking the reaction of power alarm circuit. 系統啟動、裝載 System starting up and loading. 工程師站起動程序。 Starting procedure of engineer station 操作站起動程序。 Starting procedure of engineer station 控制站起動：通電后，調出系統狀態畫面，確診狀態正常。 DCS系統調試方案 DCS Test Scheme Control station starting: After making contact, selecting system status screen ans making sure it normal. 裝載操作 Loading operation.。 各站裝載程序詳見說明書。 All loading procedures refer to manufacture instruction. 系統診斷及冗余試驗 System diagnosis and redundancy testing. 調出系統診斷畫面，對各站、臺等進行診斷檢查。 Selecting system diagnosis screen, and checking. 對系統的各種冗余模件，人為地模擬故障（通過切斷電源；拔掉電源插頭、插卡等方法），觀察備用模件能否在規定的時間內運行，并在操作臺上觀察切換過程，觀察自動切換過程是否正常。 Under the term of man simulation default, observing the running of spare module within specified time and converting. Inspecting automatic converting is normal or not. a) 電源冗余試驗 Power supply spare testing. b) 通訊冗余試驗 Communication spare testing. c) 雙重化控制器冗余試驗 Spare testing of double—control controller. d) 操作站冗余試驗 Operating station spare testing. e) 打印機熱備用試驗 Heatintg spare testing of printer 畫面測試 Screen Testing: 1) 流程圖畫面測試： Screen testing of flow—process. a) 流程畫面以 Pamp。I圖形式顯示，頁數及畫面內容應符合組態要求。 Showing flow, in from of and content shall be pliance with function requirement. DCS系統調試方案 DCS Test Scheme b) 畫面靜態顯示檢查： Static display of screen testing: * 檢查標題的位置、顏色、文字說明。 Checking title including site, color and word description. * 圖形的形狀、大小、位置、顏色。 Shape, size, site and color of picture. * 工藝管線的寬度、位置、顏色及進出接頭。 Width, site, color and inlet or outlet connector of process pipeline. * 測量變量的符號、文字、大小、位置、顏色。 Symbol, word, size, site, color of measured variables. * 儀表信號的箭頭、寬度、位置、內容。 Slope, width, site and content of instrument signal. * 頁連接符號的形狀、大小、位置、顏色、進出箭頭。 Shape, size, site, color, and inlet and outlet slope of page nexto page. * 工程測量單位符合設計要求。 Engineering measurement unit shall ply with design. c) 畫面動態顯示檢查： Active display of screen testing. * 測量變量的變化值應在系統可識別的精度范圍內。 Variable range shall be within the pricision recognized by system. * 閥、泵 運行狀態的顏色變化。 Color change of running status of pump or valve. * 報警狀態變化，且應是正確的優先級別。 Change of alarm status, which are right priority level. d) 從流程畫面選擇回路，進行調整設定值、控制模式（自動 /手動）和手動輸出的試驗。 Selecting loop from flow screen and regulating set data, control model (Auto/ manual ) and manual output. 2) 總貌畫面測試 Genera appearance screen testing: a) 確認總貌畫面已按組態數據表組態。 Making sure general appearance functioned according to function data. b) 檢查總貌畫面每個區內組和單元的正確組態。 DCS系統調試方案 DCS Test Scheme Examining correct function of each unit and group of general appearance. 3) 組畫面調試 Group—screen Testing: a) 確認組畫面中回路，與總貌畫面中描述的組一致。 Affirming loops of group—screen corresponding with those of general appearance screen. b) 各測量值、設定值、模擬和數字形式的輸出均正確組態。 Measuring data, specified data, simulation and