04操作與配置ciscoios設備-文庫吧
2024-12-25 07:43 本頁面
【正文】 tion Dialog Continue with configuration dialog? [yes/no]:yes At any point you may enter a question mark 39。?39。 for help. Use ctrlc to abort configuration dialog at any prompt. Default settings are in square brackets 39。[ ]39。. Setup模式 wg_ro_c con0 is now available Press RETURN to get started. 用戶模式 提示 wg_ro_c 路由器啟動時在控制臺上的輸出內容 控制臺 Setup: 初始配置對話框 Routersetup System Configuration Dialog Continue with configuration dialog? [yes/no]: y At any point you may enter a question mark 39。?39。 for help. Use ctrlc to abort configuration dialog at any prompt. Default settings are in square brackets 39。[]39。. Basic management setup configures only enough connectivity for management of the system, extended setup will ask you to configure each interface on the system Would you like to enter basic management setup? [yes/no]: n 預先瀏覽端口配置情況 First, would you like to see the current interface summary? [yes]: Interface IPAddress OK? Method Status Protocol BRI0 unassigned YES unset administratively down down BRI0:1 unassigned YES unset administratively down down BRI0:2 unassigned YES unset administratively down down Ether0 unassigned YES unset administratively down down Serial0 unassigned YES unset administratively down down ? 自檢過程中所找到的端口 設置全局參數 初始化全局參數 Configuring global parameters: Enter host name [Router]:wg_ro_c The enable secret is a password used to protect access to privileged EXEC and configuration modes. This password, after entered, bees encrypted in the configuration. Enter enable secret: cisco The enable password is used when you do not specify an enable secret password, with some older software versions, and some boot images. Enter enable password: sanfran The virtual terminal password is used to protect access to the router over a work interface. Enter virtual terminal password: sanjose Configure SNMP Network Management? [no]: 設置全局參數 (續 ) 初始化協議配置 Configure LAT? [yes]: n Configure AppleTalk? [no]: Configure DEC? [no]: Configure IP? [yes]: Configure IGRP routing? [yes]: n Configure RIP routing? [no]: Configure CLNS? [no]: Configure IPX? [no]: Configure Vines? [no]: Configure XNS? [no]: Configure Apollo? [no]: 設置端口參數 BRI interface needs isdn switchtype to be configured Valid switch types are : [0] none..........Only if you don39。t want to configure BRI. [1] basic1tr6....1TR6 switch type for Germany [2] basic5ess....ATT 5ESS switch type for the US/Canada [3] basicdms100..Northern DMS100 switch type for US/Canada [4] basic3....NET3 switch type for UK and Europe [5] basicni......National ISDN switch type [6] basicts013...TS013 switch type for Australia [7] ntt...........NTT switch type for Japan [8] vn3...........VN3 and VN4 switch types for France Choose ISDN BRI Switch Type [2]: Configuring interface parameters: Do you want to configure BRI0 (BRI dchannel) interface? [no]: Do you want to configure Ether0 interface? [no]: y Configure IP on this interface? [no]: y IP address for this interface: Sub mask for this interface [] : Class A work is , 24 sub bits。 mask is /24 Do you want to configure Serial0 interface? [no]: 設置腳本的確認與應用 The following configuration mand script was created: hostname Router enable secret 5 $1$/CCk$ enable password sanfran line vty 0 4 password sanjose no snmpserver ! no appletalk routing no deet routing ip routing no clns routing no ipx routing no vines routing no xns routing no apollo routing isdn switchtype basic5ess interface BRI0 shutdown no ip address ! interface Ether0 no shutdown ip address no mop enabled ! interface Serial0 shutdown no ip address text omitted end [0] Go to the IOS mand prompt without saving this config. [1] Return back to the setup without saving this config. [2] Save this configuration to nvram and exit. Enter your selection [2]: Console wg_ro_c wg_ro_cenable wg_ro_c wg_ro_cdisable wg_ro_c wg_ro_clogout wg_ro_c con0 is now available Press RETURN to get started. 用戶模式提示 特權模式提示 登入路由器 只要所輸命令串在全部命令中是唯一的，可以將一個命令盡可能地簡寫， 路由器在用戶模式下的命令清單 wg_ro_c? Exec mands: accessenable Create a temporary AccessList
教學課件相關推薦
鄂ICP備17016276號-1