【正文】 DB ? 。顯示值高位值DWZ DB ? 。顯示值地位置order db ? stop db ? 。電機啟停標志BUF db ? count dw ? 。count變量存儲低脈沖寬度，其值越大電機轉的速度越慢direct db ? 。diret=ffh表示正轉，direct=0表示反轉PACS DB ? 。A口初始化值XDSJ DB ? 。洗滌結束時間PXSJ DB ? 。漂洗結束時間SET40 EQU 00110010B 。8254計數器0控制字，方式1SET41 EQU 01010100B 。8254計數器1控制字，方式2JSCZ0 EQU 470 。470定時1s，計數器0計數初值JSCZ1 EQU 100 。計數器1計數初值SET5 EQU 10001001B 。8255控制字，方式0YANSHI DD ? 。延時子程序設定值 KEY DB ? 。按鍵狀態K0 DB ? 。電源按鍵次數K1 DB ? 。啟停鍵按鍵次數K2 DB ? 。水位設置鍵按鍵次數K3 DB ? 。洗滌鍵按鍵次數NUM0 DB ? 。電源鍵2種狀態NUM1 DB ? 。啟停鍵2種狀態 NUM2 DB ? 。水位設置鍵3種狀態NUM3 DB ? 。洗滌鍵1種狀態DY DB ? 。電源鍵當前狀態QT DB ? 。啟停鍵當前狀態SW DB ? 。水位設置鍵當前狀態XIDI DB ? 。清潔程序設置鍵當前狀態DATA ENDSCODE SEGMENT USE16 ASSUME CS:CODE, DS:DATA ORG 4000HBEG: JMP START。ADDDCCCBBBAAZZT DB 0EH,0CH,0DH,09H,0BH,03H,07H,06H 。正轉表。AABBBCCCDDDAAFZT DB 06H,07H,03H,0BH,09H,0DH,0CH,0EH 。反轉表TAB DB 0C0H,0F9H,0A4H,0B0H,99H,92H,82H,0F8H,80H,90H 。字型碼表START: MOV AX,DATA MOV DS,AX MOV DX,PORTB OR AL,00010000B OUT DX,AL CALL ZTCS 。狀態初始子程序S00: CALL C8255 。8255初始化子程序 CALL C8254 。8254初始化子程序S0: CALL JPSM 。鍵盤掃描子程序 CALL JPCL 。鍵盤處理子程序 CALL ZTSET 。狀態設置子程序 AND DY,01H CMP DY,0 。電源狀態判斷 JNE S1 。為開跳轉到S1 MOV DX,PORTA MOV AL,PACS OR AL,00000001B OUT DX,AL MOV DX,PORTC1 MOV EAX,0F0F0F0FH 。關LED OUT DX,EAX CALL ZTCS JMP S0 。跳回繼續等待電源啟動S1: MOV DX,PORTA MOV AL,PACS AND AL,11111110B 。電源指示燈亮 MOV PACS,AL OUT DX,AL MOV DX,PORTC1 MOV EAX,0F000A05H。開LED OUT DX,EAX S2: CMP QT,0 JNE S5 。開啟，跳轉 CMP SW,0 。查看水位狀態是否為低 JNE S3 MOV XSDK,PORTA3 MOV XSZ,1 CALL XSCL CALL LEDXS 。第三片8255顯示01，表示低水位 CMP XIDI,0 。是否為標志洗滌，否跳轉 JNE S41 MOV AL,PACS AND AL,11011111B OR AL,01000100B MOV PACS,AL MOV DX,PORTA OUT DX,AL 。標準洗滌小燈亮 MOV XSDK,PORTA2 MOV XSZ,30 CALL XSCL CALL LEDXS JMP S0 。跳回繼續掃描鍵盤S3: CMP SW,1 。查看水位狀態是否為中 JNE S4 MOV XSDK,PORTA3 MOV XSZ,2 CALL XSCL CALL LEDXS 。第三片8255顯示02，表示中水位 CMP XIDI,0 。是否為標志洗滌，否跳轉 JNE S41 MOV AL,PACS AND AL,11011111B OR AL,01000000B MOV PACS,AL MOV DX,PORTA OUT DX,AL 。標準洗滌小燈亮 MOV XSDK,PORTA2 MOV XSZ,30 CALL XSCL CALL LEDXS JMP S0 S4: MOV XSDK,PORTA3 MOV XSZ,3 CALL XSCL CALL LEDXS 。第三片8255顯示03，表示高水位 CMP XIDI,0 。是否為標志洗滌，否跳轉 JNE S41 MOV AL,PACS AND AL,11011111B OR AL,01000000B MOV PACS,AL MOV DX,PORTA OUT DX,AL 。標準洗滌小燈亮 MOV XSDK,PORTA2 MOV XSZ,30 CALL XSCL CALL LEDXS JMP S0S41: CMP XIDI,1 JNE S42 MOV AL,PACS AND AL,10111111B OR AL,00100100B MOV PACS,AL MOV DX,PORTA OUT DX,AL ?？焖偾鍧嵭袅? MOV XSDK,PORTA2 MOV XSZ,22 CALL XSCL CALL LEDXS JMP S0 S42: MOV AL,PACS AND AL,11111011B OR AL,01100000B MOV PACS,AL MOV DX,PORTA OUT DX,AL MOV XSDK,PORTA2 MOV XSZ,10 CALL XSCL CALL LEDXS JMP S0 S5: MOV AL,PACS AND AL,11111101B 。啟動指示燈開啟 MOV PACS,AL MOV DX,PORTA OUT DX,AL CMP XIDI,0 JNE S51 。是否設置為標準洗滌程序，否跳轉 CALL BZXD 。標準洗滌子程序 JMP S53 S51: CMP XIDI,1 JNE S52 MOV XSDK,PORTA2 MOV XSZ,22 CALL XSCL CALL LEDXS 。剩余秒數顯示25 CALL KSXD ?？焖傧礈熳映绦? JMP S53S52:MOV XSDK,PORTA2 MOV XSZ,10 CALL XSCL CALL LEDXS CALL SGXD JMP S53 S53: MOV DX,PORTB MOV AL,0 OUT DX,AL 。蜂鳴器響S8: CALL JPSM 。鍵盤掃描子程序 CALL JPCL CALL ZTSET CMP QT,0 。是否按下啟停鍵 JNE S8 。等待啟停鍵按下 MOV DX,PORTB OR AL,00010000B OUT DX,AL 。關蜂鳴器 MOV AL,PACS OR AL,00000010B MOV PACS,AL MOV DX,PORTA OUT DX,AL 。關啟停小燈 JMP S00 MEXIT: JMP MEXIT 。主程序結束 。8255初始化程序C8255 PROC NEAR PUSHA MOV DX,PORTK MOV AL,89H OUT DX,AL MOV DX,PORTK1 MOV EAX,89808080H 。寫控制字 OUT DX,EAX MOV DX,PORTA1 MO