【正文】 are verified. Table : Test Parameters for Testing Parameter Unit Test 1 5 Test 6 8 Test 9 15 Test 16 18 Downlink power allocation A? dB 0 0 0 0 B? dB 0 (Note 1) 0 (Note 1) 0 (Note 1) 0 (Note 1) ocN at antenna port dBm/15kHz 98 98 98 98 Symbols for unused PRBs OCNG (Note 2) OCNG (Note 2) OCNG (Note 2) OCNG (Note 2) Modulation QPSK 16QAM 64QAM 16QAM Note 1: 0?BP Note 2: These physical resource blocks are assigned to an arbitrary number of virtual UE39。 s with one PDSCH per virtual UE。 the data transmitted over the OCNG PDSCHs shall be uncorrelated pseudo random data, which is QPSK modulated. Release 10 3GPP 353 3GPP TS (202106) 353 Table : Minimum performance (FRC) Test number Bandwidth Reference Channel OCNG Pattern Propagation Condition Correlation Matrix and Antenna Configuration Reference value UE Category Fraction of Maximum Throughput (%) SNR (dB) 1 10 MHz FDD FDD EVA5 1x2 Low 70 15 2 10 MHz FDD FDD ETU70 1x2 Low 70 15 3 10 MHz FDD FDD ETU300 1x2 Low 70 15 4 10 MHz FDD FDD HST 1x2 Low 70 15 5 MHz FDD FDD EVA5 1x2 Low 70 15 6 10 MHz FDD FDD EVA5 1x2 Low 70 25 7 10 MHz FDD FDD ETU70 1x2 Low 30 25 8 10 MHz FDD FDD ETU300 1x2 High 70 25 9 3 MHz FDD FDD EVA5 1x2 Low 70 15 10 5 MHz FDD FDD EVA5 1x2 Low 70 25 11 10 MHz FDD FDD EVA5 1x2 Low 70 25 12 10 MHz FDD FDD ETU70 1x2 Low 70 25 13 10 MHz FDD FDD EVA5 1x2 High 70 25 14 15 MHz FDD FDD EVA5 1x2 Low 70 25 15 20 MHz FDD FDD EVA5 1x2 Low 70 35 16 3 MHz FDD FDD ETU70 1x2 Low 30 15 17 10 MHz FDD FDD ETU70 1x2 Low 30 15 18 20 MHz FDD FDD ETU70 1x2 Low 30 15 The normative reference for this requirement is TS [2] clause . Test description Initial conditions Initial conditions are a set of test configurations the UE needs to be tested in and the steps for the SS to take with the UE to reach the correct measurement state. Configurations of PDSCH and PDCCH before measurement are specified in Annex . Test Environment: Normal, as defined in TS [7] clause . Frequencies to be tested for full allocation: Mid Range, as defined in TS [7] clause . Frequencies to be tested for 1PRB allocation: Low Range, as defined in TS [7] clause . Channel Bandwidths to be tested: As specified per test number in Table as defined in TS [7] clause Release 10 3GPP 354 3GPP TS (202106) 354 1. Connect the SS, the faders and AWGN noise source to the UE antenna connectors as shown in TS [7] Annex A, Figure . 2. The parameter settings for the cell are set up according to Table as appropriate. 3. Downlink signals are initially set up according to Annex C0, and Annex and uplink signals according to Annex and . 4. Propagation conditions are set according to Annex . 5. Ensure the UE is in State 3ARF according to TS [7] clause . Message contents are defined in clause . Test procedure 1. SS transmits PDSCH via PDCCH DCI format 1A for C_RNTI to transmit the DL RMC according to Tables and . The SS sends downlink MAC padding bits on the DL RMC. 2. Set the parameters of the bandwidth, MCS, reference channel, the propagation condition, the correlation matrix and the SNR according to Tables appropriate. 3. Measure the average throughput for a duration sufficient to achieve statistical significance according to Annex G clause . Count the number of NACKs, ACKs and statDTXs on the UL during each subtest and decide pass or fail according to Tables and in Annex G clause . 4. Repeat steps from 1 to 3 for each subtest in Table as appropriate. Message contents Message contents are according to TS [7] clause . Test requirement Table the primary level settings. The fraction of maximum throughput percentage for the downlink reference measurement channels specified in Annex A clause for each throughput test shall meet or exceed the specified value in Table for the specified SNR including test tolerances for all throughput tests. Release 10 3GPP 355 3GPP TS (202106) 355 Table : Test requirement (FRC) Test number Bandwidth Reference Channel OCNG Pattern Propagation Condition Correlation Matrix and Antenna Configuration Reference value UE Category Fraction of Maximum Throughput (%) SNR (dB) 1 10 MHz FDD FDD EVA5 1x2 Low 70 15 2 10 MHz FDD FDD ETU70 1x2 Low 70 + 15 3 10 MHz FDD FDD ETU300 1x2 Low 70 + 15 4 10 MHz FDD FDD HST 1x2 Low 70 15 5 MHz FDD FDD EVA5 1x2 Low 70 + 15 6 10 MHz FDD FDD EVA5 1x2 Low 70 + 25 7 10 MHz FDD FDD ETU70 1x2 Low 30 + 25 8 10 MHz FDD FDD ETU300 1x2 High 70 + 25 9 3 MHz FDD FDD EVA5 1x2 Low 70 +1 15 10 5 MHz FDD FDD EVA5 1x2 Low 70 + 25 11 10 MHz FDD FDD EVA5 1x2 Low 70 + 25 12 10 MHz FDD FDD ETU70 1x2 Low 70 + 25 13 10 MHz FDD FDD EVA5 1x2 High 70 + 25 14 15 MHz FDD FDD EVA5 1x2 Low 70 + 25 15 20 MHz FDD FDD EVA5 1x2 Low 70 + 35 16 3 MHz FDD FDD ETU70 1x2 Low 30 + 15 17 10 MHz FDD FDD ETU70 1x2 Low 30 + 15 18 20 MHz FDD FDD ETU70 1x2 Low 30 + 15 FDD PDSCH Single Antenna Port Performance (Release 9 and forward) Editor’s note: This clause is inplete. The following aspects are either missing or not yet determined: Test tolerance is undefined Test purpose Same test purpose as in clause . Test applicability This test applies to all types of EUTRA FDD UE release 9 and forward. Minimum conformance requirements Same minimum conformance requirements as in clause with the following exceptions: Instead of Table ? use Table . Release 10 3GPP 356 3GPP TS (202106) 356 Instead of Table ? use Table . Table : Test Parameters for Testing Para