【正文】 e netmask for Network Interface vif1 []: 輸入虛擬網卡的掩碼，默認就直接回車； Should virtual interface vif1 take over a partner virtual interface during failover? [n]: y 是否允許虛擬網卡在故障時切換到另一個機頭上，輸入y； The clustered failover software is not yet licensed. To enable network failover, you should run the 39。 mand for clustered failover. 會提示說沒有輸入Clustered failover功能的license，需要輸入才能實現網絡切換功能； Please enter the partner virtual interface name to be taken over by vif1 []: vif1 輸入另一個機頭上的會被切換過來的虛擬網卡的名字； Please enter media type for vif1 {100txfd, tpfd, 100tx, tp, auto (10/100/1000)} [auto]: 輸入虛擬網卡的類型，一般是自適應，選默認auto； Please enter the IP address for Network Interface e0c []: 輸入網卡e0c的IP地址，不設置就直接回車； Should interface e0c take over a partner IP address during failover? [n]: n 是否允許網卡e0c在故障時切換到另一個機頭上，這里不配置就輸入n； Please enter the IP address for Network Interface e0d []: 輸入網卡e0d的IP地址，不設置就直接回車； Should interface e0d take over a partner IP address during failover? [n]: n 是否允許網卡e0d在故障時切換到另一個機頭上，這里不配置就輸入n； Would you like to continue setup through the web interface? [n]: n 問是否通過web方式來進行繼續的安裝，輸入n，不需要； Please enter the name or IP address of the default gateway: 輸入默認網關的名字和IP地址，無須輸入就直接回車； The administration host is given root access to the filer39。回車?yán)^續安裝。 you may add more disks to it later using the aggr add mand. Now unpack the tar file provided on the tar floppies into the root directory of the filer. When you are done, type download to install the boot image on the hard disk and reboot to begin using the new image. Mon Mar 20 09:26:41 GMT [init_java:warning]: Java disabled: Missing /etc/java/. Mon Mar 20 09:26:41 GMT [:info]: Replay begins for EMS boottime cache Mon Mar 20 09:26:41 GMT [:info]: Replay ends for EMS boottime cache Mon Mar 20 09:26:41 GMT [:info]: Firmware is uptodate on all disk drives Mon Mar 20 09:26:41 GMT [10/100/1000VI/e0a:info]: Ethernet e0a: Link up Mon Mar 20 09:26:46 GMT [10/100/1000VI/e0b:info]: Ethernet e0b: Link down, check cable Mon Mar 20 09:26:47 GMT [d_servlet:warning]: Java Virtual Machine not accessible There are 5 spare disks。 partner ID: unknown () System Serial Number: 1071155 (headb) System Rev: E0 slot 0: System Board Processors: 2 Memory Size: 2048 MB slot 0: Dual 10/100/1000 Ethernet Controller VI e0a MAC Address: 00:a0:98:03:88:12 (auto1000tfdup) e0b MAC Address: 00:a0:98:03:88:13 (autounknowndown) e0c MAC Address: 00:a0:98:03:88:10 (autounknowncfg_down) e0d MAC Address: 00:a0:98:03:88:11 (autounknowncfg_down) slot 0: FC Host Adapter 0a 8 Disks: 1 shelf with ESH2 slot 0: FC Host Adapter 0b 8 Disks: 1 shelf with ESH2 slot 0: Fibre Channel Target Host Adapter 0c slot 0: Fibre Channel Target Host Adapter 0d slot 0: SCSI Host Adapter 0e slot 0: NetApp ATA/IDE Adapter 0f (0x000001f0) 245MB slot 3: NVRAM Memory Size: 512 MB 2，使用license命令來添加所有已購買的license，如下； headb license add XXXXXXX A cifs license has been installed. Run cifs setup to enable cifs. headb Mon Mar 20 09:28:44 GMT [rc:notice]: cifs licensed headb license add XXXXXXX A cluster license has been installed. Clustered Failover will be enabled upon reboot. Make sure that each individual service is licensed on both nodes or on neither node. Remember to configure the network interfaces for the other node. headb Mon Mar 20 09:29:08 GMT [rc:notice]: cluster licensed Mon Mar 20 09:29:17 GMT [:info]: /etc/crash/ processing pleted Mon Mar 20 09:29:18 GMT [:info]: Generating /etc/crash/ Mon Mar 20 09:29:18 GMT [:info]: (/etc/crash/) generation pleted Mon Mar 20 09:29:18 GMT [:info]: Generating /etc/crash/ Mon Mar 20 09:29:18 GMT [:info]: (/etc/crash/) generation pleted headb license add XXXXXXX A fcp license has been installed. Run 39。 to start the FCP service. Also run 39。 if necessary to configure LUNs. FCP enabled. headb Mon Mar 20 09:29:39 GMT [rc:notice]: fcp licensed headb license add XXXXXXX A iscsi license has been installed. Run 39。 to start the iSCSI service. Also run 39。 if necessary to configure LUNs. iSCSI enabled. headb Mon Mar 20 09:29:53 GMT [rc:notice]: iscsi licensed headb cifs setup 使用此命令來配置CIFS； This process will enable CIFS access to the filer from a Windows(R) system. Use ? for help at any prompt and CtrlC to exit without mitting changes. Your filer does not have WINS configured and is visible only to clients on the same subnet. Do you want to make the system visible via WINS? [n]: 問是否需要使用WINS來控制系統的訪問，不需要就輸入n； A filer can be configured for multiprotocol access, or as an NTFSonly filer. Since multiple protocols are currently licensed on this filer, we remend that you configure this filer as a multiprotocol filer (1) Multiprotocol filer (2) NTFSonly filer Selection (12)? [1]: 1 因?yàn)槭褂藐嚵械沫h(huán)境是一個異構平臺的環境，所以要選擇1； CIFS requires local /etc/passwd and /etc/group files and default files will be created. The default passwd file contains entries for 39。, 39。, and 39。. Enter the password for the root user []: 輸入登陸用戶root的密碼； Retype the password: 重復一邊； The default name for this CIFS server is 39。. Would you like to change this name? [n]: n 問是否要修改機頭的名字，不用就輸入n； Data ONTAP CIFS services support four styles of user authentication. Choose the one from the list below that best suits your situation. (1) Active Directory