【正文】 nd the CSA Monogram with the “C US” indicator.Caution Wording: WARNING: RISK OF ELECTRIC SHOCK. CAN CAUSE INJURY OR DEATH:DISCONNECT ALL REMOTE ELECTRIC POWER SUPPLIES BEFORE SERVICING. AVERTISSEMENT. RISQUE DE CHOCS ELECTRIQUES.PEUT CAUSER DES BLESSURES ET MEME ENTRAINER LA MORT. COUPER LES SOURCES D’ALIMENTATION A DISTANCE AVANT LE DEPANNAGE.The above caution wording may appear on a separate adhesive type nameplate affixed near to the main nameplate. Labels not affixed to removable cover unless otherwise specified.USE COPPER SUPPLY WIRES. UTILISER DES FILS D’ALIMENTATION EN CUIVREThe above caution wording appears on a separate adhesive type label near the main terminal block.The statement “for use with indoor unit, CARRIER MODEL FE4ANF005”.Suitable wiring diagram is provided on each unit (paper wiring diagram is affixed to the access panel inside surface).Suitable wiring diagram is provided on the unit.Installation operating manual is provided with each outdoor unit.Notes: 1. Jurisdictions in Canada may require these markings to be also in French. It is the responsibility of the customer to provide bilingual marking, where applicable, in accordance with the requirements of the Provincial Regulatory Authorities.2. The product may bear the CSA logo, or CSA with US indicator, or CSA with C US indicator.ALTERATIONS1. The markings are as noted above.FACTORY TESTS409613868. Dielectric Withstand Test: The equipment, upon pletion of manufacture and before shipment, shall withstand, for not less than one second, without breakdown, the application of the following ac voltages, between live parts and exposed metal parts:(a) 1,000V for units with a motor rated at less than 1/2 hp and rated 250V or less.(b) 1,000V plus twice rated voltage for all other units.For units which include extralowpotential circuits (30V or less), the test is to be conducted with the extralowpotential circuit connected to the cabinet, chassis, or other dead metal part, so that the potential which is applied between the primary circuit and the exposed metal parts, is applied simultaneously between the primary circuit and the extralowpotential circuit.(c) For units which include extralowpotential circuits。MASTER CONTRACT: 218317 REPORT: 1965853 PROJECT: 1965853 Edition 1: June 28, 2007。 Project 1965853 – Toronto Prepared by Contents: Certificate of Compliance Page 1 Supplement to Certificate of Compliance Page 1Descriptive Report and Test Results Pages 1 to 80Illustrations Ills 1 to 9Figures Figs 1 to 14Attachment Atts. A and BPRODUCTSCLASS 1211 05 COMFORT CONDITIONING EQUIPMENT (ELECTRICAL) – Air ConditionersCLASS 1211 85 COMFORT CONDITIONING EQUIPMENT (ELECTRICAL) CERTIFIED TO . STANDARDSCentral Air Conditioners, ducted unit, permanently connected, consisting of an air cooled outdoor unit and a matching indoor unit, using refrigerant R410A, with model numbers and ratings shown as follows:PART A: Outdoor unit, BORA Model 24CHSRA, rated 208/230V, 60Hz, 1 phase.PART B: Outdoor unit, BORA Model 30CHSRA, rated 208/230V, 60Hz, 1 phase.PART C: Indoor unit, CARRIER Model FE4ANF005, rated 208/230V, 60Hz, 1 phase.APPLICABLE REQUIREMENTSCAN/ No. 23605 Heating and Cooling Equipment.UL Standad No. 1995 Heating and Cooling Equipment.MARKINGSINDOOR UNIT: Not applicable. The indoor unit is an UL listed fan coil unit and is marked in accordance with UL certification report.OUTDOOR UNIT: A CSA Accepted or UL Recognized adhesive type nameplate Certified for outdoor use, is affixed to the outside of the cabinet bears the submittor39。 500V between the extralowpotential circuit and exposed metal parts.Note: The test specified in Item (c) may be waived, if the extralowpotential circuit is grounded or Class 2.409613869. Pressure Test for Refrigerant Leakage: At the pletion of manufacture and before shipment, the plete refrigeration system of the equipment shall be tested and proved tight at pressures not less than the highest of the following:(a) The design pressures marked on the data plate for the device.(b) The minimum test pressures tabulated below.RefrigerantMinimum Design Pressure*Low SideHigh SidekPapsigkPapsig229931441917278500703102140020350211171622082302134a593861282186R407C11421662191318R410A16222353075446Notes:*A method other than pressure testing at the design pressure may be employed if it can be demonstrated that the alternative test method produces results that are at least equivalent to the pressure test method.The leakage test on the plete system may be conducted at the indicated low side pressure if final assembly of the equipment is pleted with flaretype fittings or telescoped tubing joints that are sealed with silver solder, brazing, or equivalent means provided the high side parts are CSA Certified refrigerant containing ponent parts, or individually tested at not less than high side pressure indicated.Warning: The factory test(s) specified may present a hazard of injury to personnel and/or property and should only be performed by persons knowledgeable of such hazards and under conditions designed to minimize the possibility of injury.DESCRIPTIONThe description of each section is grouped as follow:SectionNumber. Description10 Markings20 Cabinet and metal enclosures30 Non metallic enclosure and parts40 Refrigeration system ponents50 Compressors60 Fan motors70 Electrical ponents80 Internal wiringAttachment DescriptionA. Installation manual of Bora outdoor units.B. Installation manual of Carrier fan coil indoor units.PRODUCT DECRIPTION:The products covered in report are central air conditioning systems each consisting of an outd