【正文】 cation of water pressure varies with the change of height difference principle, use rise and fall of control stepper motor to control the bit rate. Intravenous drip speed can be set with keyboard, set range of 20150 (drops/min), control about 10% error range in 1 drop. From change the set point to the basic stability of the whole process of dropping speed adjustment time is less than 3 minutes. At the same time can send out alarm signal when the water is below the alarming. Keywords Intravenous drip speed； the step motor； MCU； alarm system 目 錄 1 目 錄 摘 要 ................................................................................................................................................. i Abstract .............................................................................................................................................iii 第 1 章 緒 論 ............................................................................................................................... 1 課題研究意義 ........................................................................................................................... 1 國內外現狀 ............................................................................................................................... 2 主要研究?jī)?nèi)容 ........................................................................................................................... 3 第 2 章 系統方案選擇與論證 ........................................................................................................ 4 各模塊方案選擇和論證 ............................................................................................................. 4 液體點滴速度及儲液瓶液面檢測 ......................................................................................... 4 液瓶液面檢測 ..................................................................................................................... 5 鍵盤方案 ............................................................................................................................ 6 顯 示方案 ............................................................................................................................ 6 電機系統方案 ..................................................................................................................... 6 點滴速度控制方案 .............................................................................................................. 7 方案的確定 ............................................................................................................................... 7 第 3 章 系統硬件設計與實現 ........................................................................................................ 9 系統硬件基本組成部分 ............................................................................................................. 9 電路模塊電路設計 .................................................................................................................... 9 液體點滴速度檢測電路設計 ................................................................................................ 9 鍵盤控制電路 ....................................................................................................................11 步進電機驅動電路 .............................................................................................................11 系統原理圖 ............................................................................................. 錯誤 !未定義書簽。同時在水到達警戒線以下時能發出報警信號。點滴速度可用鍵盤來設定，設定范圍為 20150(滴 /分 )， 每滴 誤差范圍 控制 在 10%左右 。該裝置由水滴速度測試系統、水速控制系統、顯示裝置、單片機系統、鍵盤和報警等系統組成。常規臨床輸液，普遍采用掛瓶輸液，并用眼睛觀察，依靠手動夾子來控制輸液速度，不易精確控制輸液速度，而且工作量大。輸液過快，可能會導致中毒，更嚴重時會導致水腫和心力衰竭 。摘 要 基于單片機的液體點滴速度監控裝置設計 摘 要 摘 要 靜脈輸液是一種最常用的臨床治療方法，是護理專業的一項常用給藥治療技術。臨床上應根據藥物和患者情況不同配以適當?shù)妮斠核俣?。輸液過慢則可能發生藥量不夠或無謂地延長輸液時間，使治療受影響并給患者和護理工作增加不必要的負擔。 本系統是利用單片機 設計并制作一個智能化的液體點滴速度監測與控制裝置 。應用水的壓強隨著高度差的變化而變化的原理，利用控制步進電動機的升降來控制點滴速度。從改變?cè)O(shè)定值起到點滴速度基本穩定整個過程的調整時間小于 3 分鐘。 關鍵字 點滴速度 ； 步進電動機 ； 單片機 ； 報警系統 Abstract Abstract Intravenous infusion is one of the most monly used in clinical treatment, is a monly used medication nursing professional technology. Should be based on drug and clinical patients is different with the appropriate transfusion speed. Infusion too quickly, it may cause poisoning, will lead to more serious edema, and congestive heart failure。 輸液管的機械控制 ............................................................................................................ 12 元器件說明 ............................................................................................................................. 12 AT89C52 .......................................................................................................................... 12 集成運算放大器 LM324N.................................................................................................. 14 電壓比較器件 LM339........................................................................................................ 18 步進電機及其驅動 ULN2021 ............................................................................................. 21 1602 型 LCD ..................................................................................................................... 23 第 4 章 系統軟件設計 ................................................................................................................ 25 點滴速度測量 ......................................................................................................................... 25 點滴速度控制 ......................................................................................................................... 26 鍵盤掃描 ................................................................................................................................ 26 液晶顯示 .........................................................................