【正文】 靜電防護的”警式看板” ? 10 _____ Are the daily wrist strap checks being performed and recorded the results ? 靜電手環是否每班做檢查及記錄檢查結果呢 ? 11 _____ Does the wrist strap resistance measurement path go from the wearer39。 Conductive Bag Antistatic Magazine 導電袋及抗靜電管 (2) 26 Caution Label 提醒標籤 1. A yellow ESD caution label shall be attached no conductive bag and one side of packing box. 黃色的 ESD 警告標誌必須貼在導電袋及包裝箱上 . 2. Each ESD protective package shall have a contrasting ESD caution label. The caution label shall be legible to normal vision at a distance of three feet. 每件靜電防護包裝物必須有明顯的靜電警告標籤 .這靜電警告標籤必須能在三英尺外以正常目視可辨識出 . 27 AntiStatic Void Filler 抗靜電泡墊 Packing and filler materials for ESDs devices shall not turboelectric charge to greater than +/200(TCP100V) volts under normal/intended use. 靜電敏感材料的包裝及填充物當使用時不得因摩擦而產生大於 +/ 200(TCP100V) 伏特之靜電壓 . 28 Dissipative Table/Floor MAT (Optional) 靜電地氈或桌墊 (1) 1. ESD protective static /=10E5 to 10E9 ohm dissipative work surface to ESD ground resistance. 靜電防護傳導物表面至靜電接地之電阻等於或大於 10E5 歐姆 到 10E9 歐姆 2. The remended lower limit is 10E5 ohm. However a lower value may be used if local safety requirements can still be met. 建議最低的阻抗值是 10E5 歐姆 . 但是如果能夠符合當 地安全要求則低於此建議值的阻抗可以採用 . 29 3. ElectrodesTwo cylindrical kg(5 pound)electrodes with a diameter of mm ( inches) each having contacts of electrically conductive material with a ShoreA (IRHD) udometer hardness of 5070. The resistance between the two electrodes should be less than 1 kilohm when measured at 10 V or less on a metallic surface. 電極 兩個重約 公斤 (5 磅 ),直徑 公分 ( 英吋 ) 的圓柱型電極 , 每個都要有硬度在 (IRHD) 5070 間的導電物相接觸 . 兩個電極間的電阻在金屬表面及 10 伏特或更低的量測電壓下時不得大於 1 k 歐姆 . Dissipative Table/Floor MAT (Optional) 靜電地氈或桌墊 (2) 30 4. Clean electrode with a clean,lowlining cloth. or using a minimum of 70% isopodanwater to clean it. Allow electrode to air dry. 使用清潔且不會脫纖維的布料來清潔電極 .或用至少含有 70% 的異丙 醇水溶液來清潔電極 ,並讓電極在空氣中乾燥 . 5. Connect one lead of the meter to ESD ground, and the other lead to the electrode. Place electrode on the surface of the material being tested. Apply test voltage and record the resistance after the measurement has stabilized or after 15 seconds has elapsed. Remove test voltage and remove electrode from surface. 連結儀表的一端到接地點 ,另一端到電極 . 將電極置於待量測物體表面 相距至少 3 英尺 . 輸入測試電壓並在量度穩定或 15秒後記錄阻抗值 . 停止測試電壓且將電極也移開 . Dissipative Table/Floor MAT (Optional) 靜電地氈或桌墊 (3) 31 6. Perform a minimum of five tests per contiguous Floor surface material or a minimum of five tests per 5,000 Square feet of floor material, whichever is greater. A Minimum of three of the five tests should be conducted in Those areas that are subject to wear or that have chemical or Water spillage or that are visibly dirty. 在連續的地板面至少要做 5 次測試或每 5000平方英尺要做 5 次測試 ,那 種次數多就採用那種 . 5次中至少有 3次要在有受磨損 ,或受化學物 ,水污 染或看起有些髒的地方 Dissipative Table/Floor MAT (Optional) 靜電地氈或桌墊 (4) 32 ESD Protected Work Station 無靜電工作桌 (1) 1. Static dissipative ESD protective work surfaces are preferred. A direct connection to ground is remended. A resistor of 1M ohm +/ 10 % in the grounding wire is optional. 建議最好使用靜電傳導防護工作面 ,且直接連結到接地 . 接地線可加或 不加 1M +/ 10 % 電阻 . 2. When highly conductive ESD protective work surfaces are required due to the manufacturing process needs (., stainless steel), they shall be connected directly to ESD ground without a series resistor to ensure they are continuously at ground this case Ground fault circuit interrupters (GFCI) is a remendation. 當高導電性靜電防護工作面 (如 :不銹鋼工作面 )因製造部需要而設置時 , 它們需直接連結到靜電接地而不須外加一串連電阻以確定它們持續的 維持接地電位 。s hand, through the user39。ESD Best Practical Sharing TITL QRA 1 2 Index ? ESD History ? Definition of ESD Material ? Reduce ESD Damaged Methodology ? ESD Check list 3~13 14~17 18~46 47~52 Page 2 Reminder that ESD is a serious problem in the entire electronics industry. 提醒所有員工“靜電”對 IC材料的破壞是一個非常嚴重的問題 , 它是整個半導體所面臨的一項挑戰 . Why Do We Need ESD Training? 為何需要此 ESD訓練課程 ? ? It is believed that 25% of all ponent failures are a result of ESD. 相信有大約 25%的 IC材料是因靜電 (ESD)的影響而遭破壞 3 3 ? Electrical Over Stress(EOS)The exposure of an item to a current or voltage beyond its maximum ratings. EOS 指一個 IC材料受到超過其所能負荷的電壓 ,電流而遭受到破壞 的狀態 Definitions 定義 ? Electrostatic Discharge (ESD)The transfer of electrostatic charge between bodies or surfaces at different electrostatic is a subset of EOS. ESD 即靜電放電之意 .指不同電位的二個物體之間產生的電荷急驟流 動的現象 . 4 4 Conductors vs Insulators 帶靜電的絶緣體 Charged Insulator 帶靜電的導體 Charged Conductor Conductor evenly distributes charge over entire surface 平均分佈於整個表面 Opposite polarity charges can exist on the same insulator. 不同極性的電荷會同時存在絶緣體上 Conductor pletely discharges when grounded