工程制圖量測說明ppt課件-文庫吧資料
2024-11-09 20:44本頁面
【正文】 o datum A Feature axis must lie within the tolerance zone ? 有加注尺寸的位置度公差 A A 90? ?10? (2) 53 有標明多個數據的位置度公差 60 ? A B C 20 30 A B C Cylindrical tolerance zone must be perpendicular to datum A and parallel to datum B and C Datum A plane Datum B plane Datum C plane Axis of feature must be within the cylindrical tolerance zone ?10? (2) 54 MMC使用計算原則 164。 Positional tolerance with datum 164。旋轉圓形總體表面 – 選擇正確的斜面 (有角度的 ) ? Runout is the radial deviation of a circular line element or surface from a specified axis ? Runout must always be specified in relation to a datum 軸 46 A1 A2 A Full Indicator Movement must be within runout tolerance of for each circular element (line) Runout of Circular Element 47 A1 A2 A Full Indicator Movement must be within runout tolerance of for the total surface Runout of Total Surface Perform measurement for many circular element and find the lowest and highest reading to get the FIM for the total surface 48 A Tolerance of FIM for each circular element A Tolerance of FIM for each circular element Runout for Circular Element – 傾斜的面 Runout for Circular Element Right Angled Faces 49 公差 指在 FIM for all the circular element bined A 避開總體的表面 Right Angled Faces 50 位置度公差 164。旋轉圓形總體表面 164。 Parallelism of Axis in Relation to Datum Axis ? Parallelism must be measured in relation to a datum plane or axis 42 A A Tolerance zone formed by 2 planes apart and parallel to Datum A Datum A plane Surface must be within size limits and additionally restricted by the parallelism tolerance Parallelism of a Surface 43 A A tolerance zone formed by 2 planes parallel to datum A plane Datum plane A Axis of the hole must be within the dimensional limit and additionally fall within the planes of the tolerance zone 軸線到一個基準面的平行尺寸 44 Datum A Axis Feature Axis must lie within the tolerance zone for the width of the feature cylindrical tolerance zone Parallelism of Axis in Relation to Datum Axis A ? A 45 圓度和圓形度公差 164。 面之間的平行 164。 Perpendicularity of an Axis Determined by 2 Parallel Planes Tolerance Zone 164。 Perpendicularity of a Surface in Relation to a Datum Plane 164。 角的斜面 164。 Profile Unilateral Tolerance 164。 Profile WITH Datum Reference 164。 理論上存在的輪廓 164。 Staging the Part for Flatness Inspection ? 被測表面必須位于兩個平行平面之內 ? 如果只要求要素某ㄧ部分的公差值 ,兩個平面度公差ㄧ定要注明數據 25 max 這個實際的表面平坦度公差 是存在于兩個平行的面之間的 . 平面度的表示 26 Part can be staged using spherical ended pins and the point immediately above it (surface to be checked) is zero. This will enable a zero plane to be established amp。 不能超過直線度 直線度的方向 ? 22 軸心的直線度 軸線在實際中的表現 理論上軸線必須在這圓柱體的公差內浮動 圓柱公差帶 ? ? 4? 23 MMC邊界線在直線度公差的運用 ? (12d10) Actual Straightness Size Tolerance . . . 平面到產品的垂直距離 實際尺寸 MMC邊線 24 平面度公
教學課件相關推薦
鄂ICP備17016276號-1