【正文】 ceilling installationb) The following step is for ceiling installationConfigure the two switches of the camera properly, for details please refer to chapter 3.Using the camera mounting base as a template, mark the locations of the three mounting holes on the ceiling. Use screws (M4) at the locations you marked above to secure the mounting base to the ceiling. Install the camera onto the mounting base, and tighten the camera using a screw (M3). Plug the power, video and control header into the corresponding jacks on the backplane of the camera Camera connectionsThere are power, video RS232 and RS485 ports on the backplane of the camera, and cables are labeled on the terminal. Before connecting the camera, you must check the cable carefully.一、RS485/RS422and RS232 Ports Settings Ports Settings of S series video conference cameraPorts Settings of D series video conference camera二、RS485/RS422 Cortrol： Red WareRS485+/RS422+ Black WareRS485/RS422Chapter 3 Switch Settings GeneralBefore using the camera, configure the camera address, control protocol, baud rate and image flip setting. The switches, to configure these settings, are located on back panel of camera. Figure 4 shows the switches on back panel, the ON direction is marked beside the switches. SW1 SW2Figure 5 Switch Setting SW1 set the camera’s address, for detail please refer to table 1.Camera AddressSW1123456780OFFOFFOFFOFFOFFOFFOFFOFF1ONOFFOFFOFFOFFOFFOFFOFF2OFFONOFFOFFOFFOFFOFFOFF3ONONOFFOFFOFFOFFOFFOFF4OFFOFFONOFFOFFOFFOFFOFF5ONOFFONOFFOFFOFFOFFOFF6OFFONON OFFOFFOFFOFFOFF7ONONONOFFOFFOFFOFFOFF8OFFOFFOFFONOFFOFFOFFOFF9ONOFFOFFONOFFOFFOFFOFF10OFFONOFFONOFFOFFOFFOFF11ONONOFFONOFFOFFOFFOFF12OFFOFFONONOFFOFFOFFOFF13ONOFFONONOFFOFFOFFOFF14OFFONONONOFFOFFOFFOFF15ONONONONOFFOFFOFFOFF16OFFOFFOFFOFFONOFFOFFOFF17ONOFFOFFOFFONOFFOFFOFF18OFFONOFFOFFONOFFOFFOFF19ONONOFFOFFONOFFOFFOFF20OFFOFFONOFFONOFFOFFOFF………………………249ONOFFOFFONONONONON250OFFONOFFONONONONON251ONONOFFONONONONON252OFFOFFONONONONONON253ONOFFONONONONONON254OFFONONONONONONON255ONONONONONONONONTable 1 SW1camera address settingSW2 set the camera’s baud rate, control protocol and image flipping SW2SW Pos1234ProtocolOFF OFFOFFOFFONOFFOFFOFFPELCOPOFFONOFFOFFPELCODONONOFFOFFVISCAOFFOFFONOFFONOFFONOFFOFFONONOFF…………SW Pos567Baud Rate (BPS)1200OFFOFFOFF2400ONOFFOFF4800OFFONOFF9600ONONOFF19200OFFOFFONONOFFONONONONSW Pos8Image FlipImage not flipOFFImage flipONTable2: SW2 camera Protocol, Baud rate and Image Flip SettingSet the camera’s VISCA protocol, we set the camera’s address 1, baud rate 9600 bps, VISCA protocol and image not flip. The SW2 setting is list in table 3.SW2SW Pos12345678ONONOFFOFFONONOFFOFFTable 3Troubleshooting SymptomCauseRemedyNo picture displayed on the screem after turning on powerProblemes caused by the power supplySettle the power supply problemsProblems of the switchAdjust itCannot not adjust automatically as soon as the power is turned onPower supply not enoughCheck the power plugTechnical problemsrepairRomote controller does not workRemote controller is out of powerChange the batteryToo far way from the cameraUse it within 8 meters from the cameraThe picture cannot be controlled on the screemThe camera’s address,protacal or Baud rate is wrongReset themRS485/RS42RS232 connected wrong Check RS485/RS42RS232 Picture lost when the camera is rotatingPower supply is not enoughPower supply connection are looseThe video cambles don’t work wellchange the camble.The image es from the digital jack is not as good as which from the video jackChanging from analog signals to digital signal will cause some loss.Inquire the manufacturerAfter Sale ServiceDear users: in order to warrant that you can obtain good services for your products, please read the following service rules carefully: I WinYork will repair, without charge, any product proved defective in material or workmanship for a period of one year after the date of shipment. But the following cases are excluded in the warranty:　1. Abuse, unreasonable use,or mistreatment.. 　2. Damage caused by natural disaster. 　II If the product has been out of the promise date or the label of date was, you have to pay for the maintenance.Respond and Return Information1. We will respond within 24 hours after we receive the returned product.2. Before sending back the product to our pany, please contact our staff. 39 /