【正文】 on matrix and the SNR according to Table appropriate. 3. Measure the average throughput for a duration sufficient to achieve statistical significance according to Annex G clause . Count the number of NACKs, ACKs and statDTXs on the UL during each subtest and decide pass or fail according to Tables and in Annex G clause . Message contents Message contents are according to TS [7] clause with the following exceptions: Release 10 3GPP 362 3GPP TS (202106) 362 Table : SystemInformationBlockType2: Additional FDD PDSCH Single Antenna Port Performance for 1 PRB allocation with MBSFN subframes test point 1 requirement Derivation Path: TS [7] clause , Table SystemInformationBlockType2 Information Element Value/remark Comment Condition SystemInformationBlockType2 ::= SEQUENCE { mbsfnSubframeConfig ::= SEQUENCE { radioframeAllocationPeriod n1 Every radio frame is with MBSFN subframe radioframeAllocationOffset 0 subframeAllocation CHOICE { oneFrame 111111 Subframe 1, 2, 3, 6, 7, 8 is used for MBSFN FDD } } Test requirement Table the primary level settings. The fraction of maximum throughput percentage for the downlink reference measurement channels specified in Annex A clause for each throughput test shall meet or exceed the specified value in Tables the specified SNR including test tolerances for all throughput tests. Table : Test requirement 1 PRB allocation with MBSFN subframes (FRC) Test number Bandwidth Reference Channel OCNG Pattern Propagation Condition Correlation Matrix and Antenna Configuration Reference value UE Category Fraction of Maximum Throughput (%) SNR (dB) 1 10 MHz FDD FDD ETU70 1x2 Low 30 + 15 FDD PDSCH Transmit Diversity Performance (CellSpecific Reference Symbols) FDD PDSCH Transmit Diversity 2x2 Test purpose To verify the UE’s ability to receive a predefined test signal, representing a multipath fading channel that is determined by the SNR with a percentage of the information bit throughput for a specified downlink Reference Measurement Channel (RMC) not falling below a specified value for transmission on two antenna ports using transmit diversity (SFBC). Test applicability This test applies to all types of EUTRA FDD UE release 8 and forward. conformance requirements The requirements are specified in terms of the percentage of information bit throughput for the downlink reference measurement channels specified in Annex A clause , with the addition of the relevant parameters in Tables and and the downlink physical channel setup according to Table in Annex . Using this configuration the fraction of maximum throughput percentage shall meet or exceed the minimum requirements specified in Table for the specified SNR. For transmit diversity (SFBC) performance with 2 transmitter antennas as specified. Release 10 3GPP 363 3GPP TS (202106) 363 Table : Test Parameters for Testing Transmit Diversity Performance Parameter Unit Test 12 Downlink power allocation A? dB 3 B? dB 3 (Note 1) ocN at antenna port dBm/15kHz 98 Note 1: 1?BP Table : Minimum performance Transmit Diversity (FRC) Test number Bandwidth Reference Channel OCNG Pattern Propagation Condition Correlation Matrix and Antenna Configuration Reference value UE Category Fraction of Maximum Throughput (%) SNR (dB) 1 10 MHz FDD FDD EVA5 2x2 Medium 70 25 2 10 MHz FDD FDD HST 2x2 Low 70 15 The normative reference for this requirement is TS [2] clause . Test description Initial conditions Initial conditions are a set of test configurations the UE needs to be tested in and the steps for the SS to take with the UE to reach the correct measurement state. Configurations of PDSCH and PDCCH before measurement are specified in Annex . Test Environment: Normal, as defined in TS [7] clause . Frequencies to be tested: Mid Range, as defined in TS [7] clause . Channel Bandwidths to be tested: As specified per test number in Table as defined in TS [7] clause . 1. Connect the SS, the faders and AWGN noise sources to the UE antenna connectors as shown in TS [7] Annex A, Figure for antenna configuration 2x2. 2. The parameter settings for the cell are set up according to Tables and as appropriate. 3. Downlink signals are initially set up according to Annex C0, and Annex and uplink signals according to Annex and . 4. Propagation conditions are set according to Annex . 5. Ensure the UE is in State 3ARF according to TS [7] clause . Message contents are defined in clause . Test procedure 1. SS transmits PDSCH via PDCCH DCI format 1A for C_RNTI to transmit the DL RMC according to Tables and . The SS sends downlink MAC padding bits on the DL RMC. 2. Set the parameters of the bandwidth, MCS, reference channel, the propagation condition, the correlation matrix, antenna configuration and the SNR according to Tables as appropriate. 3. Measure the average throughput for a duration sufficient to achieve statistical significance according to Annex G clause . Count the number of NACKs, ACKs and statDTXs on the UL during the test interval and decide pass or fail according to Tables and in Annex G clause . Release 10 3GPP 364 3GPP TS (202106) 364 4. Repeat steps from 1 to 3 for each test interval in Table as appropriate. Message contents Message contents are according to TS [7] clause . Test requirement Table defines the primary level settings. The fraction of maximum throughput percentage for the downlink reference measurement channels specified in Annex A clause for each throughput test shall meet or exceed the specified value in Table for the specified SNR including test tolerances for all throughput tests. Table : Test require