外文翻譯---wincc在供熱站恒壓供水監控系統中的應用-其他專業-資料下載頁
【導讀】系統采用變頻調速方式自動調節誰笨點擊轉速或加、減泵。調節器、壓力傳感器、液位傳感器、動力控制線路等組成，用。在基于PID的控制方式下，操作人員在操作界面設定供水壓力，PLC. 服務器的工業以太網通訊網卡采用西門子公司的CP1612.供熱站使用Wincc組態軟件主要監控恒壓供水系統和輸煤廊兩部分。檢測恒壓供水和輸煤廊運行設備的各項參數，實現。實時數據的采集、上傳、實時顯示和記錄。控制機組運行、故障的自動停機和報。運行;變頻器再啟動3號泵運轉，知道輸出水壓達到設定值為止。水量減少，則依照“先啟后?！痹瓌t一次將水泵切除。模糊控制具有不依賴。換時機計算機程序根據事先給定的誤差范圍自動實現。屬函數采用三角形，根據現場經驗總結出模糊控制規則，如表1所示。程是離線進行的，最終得到模糊控制查詢表，如圖2所示。進入模糊控制子程序。最大節能效果，而且實現了恒壓供水的目的。變頻器在投入運行后的調試是保證系統達到最佳運行狀態的必要手段。
【正文】 e process for finding inquiries on the questionnaire process. Parametric Selection of Frequencywater system a reasonable selection pressure control parameters constant pressure to achieve energysupply system. The realization of is this objective the key is pressure control parameter selection, usually pipe work pressure control point two choice: a pipe work is the most negative pressure on constant pressure control and the other is the constant pressure pump outlet. pressure control. How will the two choices, we have to analyze simple Network pressure on the most disadvantaged constant, the water pipe work by QMAX reduced to Q1, pumps reduce speed, and water characteristic curve of A (unchanged) at the intersection point C, pump characteristic curve downward, work pressure on the most disadvantaged H0. And the pump outlet pressure constant pressure control, Ha unchanged, reduce water consumption by QMAX QI and Ha to pay to point B, water characteristic curve upward A through B, the work most disadvantaged Hb pressure into points. HbH0 lift the poor namely, energy waste, so I chose the most disadvantaged work points for the smallest head pressure control parameters. Formation pressure on the closedloop control system, making the pump speed and PID regulator set pressure match, achieve maximum energysaving effect, but the constant pressure to achieve the purpose of water supply. the converter and put into operation after the missioning of the system to ensure optimum operation of the state means necessary. According to the inverter load inertia size of the start and stop the motor when the time is not the same, Set time is too short to be accelerated when the inverter overcurrent, overvoltage decelerating protection。 Set time will lead to excessive speed converter running in the system bee regulate slow, delayed response, contingency ability is poor. Yi system at the state shortterm instability. To protect the converter is not tripping, the scene of many of them using converter increases deceleration time setting too long, the problems they bring very easily be the appearance of the normal equipment and hide, but the converter operating in lessthanoptimal state. So the scene when used according to the load driven by a different nature, testing out the permission of the shortest load increases deceleration time, setting. For the pump motor, plus deceleration time in the choice between seconds.
鄂ICP備17016276號-1