模具方面的中英文對照(編輯修改稿)
2024-08-29 20:58 本頁面
【文章內容簡介】 0。 面銑刀rad mill 圓角成型刀chamfer mill 倒角刀slot mill 槽刀taper mill 推拔銑刀dove mill 鳩尾銑刀lot mill 棒狀drill 鉆孔reamer 紋刀bore bar 搪刀tap RH 右牙刀Tap LH 左牙刀ctr Drill 中心鉆spot drill 點鉆tr bore 沉頭孔刀c. sink 魚眼孔鉆loft surface 舉升曲面coons surface 昆氏曲面ruled surface 直紋曲面revolved surface 旋轉曲面swept surface 掃描曲面draft surface 牽引曲面grinding wheel 磨砂使用的輪子quench steel 將...淬火,使冷卻stress relieving 應力消除molten 熔熱的oxide film 氧化層guide pin and sleeve, locating ring ,導邊,司筒,定位圈ejector ,ejector balde, ejector sleeve,頂針,扁頂針,頂針?biāo)就?lifters, wear plate,horn pin,斜坊,磨損板,氣頂針,O ring, water baffle, water pipe plug,O形圈,隔片,運水管道塞,water line connector,wear plate ,運水管道轉接頭,耐磨板air cylinder,hydraulic cylinder,氯壓缸,液壓缸micro switch,oil nipple, spring,開關裝置,油槍接頭,彈弓sprue bushing,early return system,澆口套,早期回撞裝置,accelerated ejectors, slied holder,加速頂針,注塑周期計數器,cycle counter,date stamper，滑塊固定板,生產日期銘牌,hot runner system ，熱流道系統chemical position 化學成份thermal conductiivity 導熱性能thermal diffusivity 熱擴散性能dimensonal stablity 尺寸穩定性能cooling effiency 冷卻效率easiler ejection 易于脫模alloy insert 合金鑲件(cooling) duct 輸送管。導管maintenance cost 維護費用ultrasonic testing 超聲波檢測crack 斷裂direct gate 直接澆口ring gate 環形澆口disk gate。disphragm gate 盤形澆口spoke gate。spider gate 輪輻澆口pinpoint gate 點澆口edge gate 側澆口submarine gate。tunnel gate 潛伏澆口fan gate 扇形澆口tab gate 護耳澆口runner plate 流道板(或冷或熱)secondary nozzle 二級噴嘴torpedo。torpedo body assembly 魚雷形組合體catridge heater 管式加熱器heat pipe 熱管 valve gate 閥式澆口force plunger。pot plunger 柱塞flash groove。spew groove 溢料槽impression。cavity block。cavity plate 凹模punch。force 凸模movable insert。loose detail 活動鑲件cavity splits。core splits(凹模拼塊) (型芯拼塊) 拼塊side core 側型芯thread plug。threaded core 螺紋型芯thread ring。threaded cavity 螺紋型環cutting wheel 切割砂輪grinding wheel 打磨砂輪abrasive material 打磨器材mould clamps。lifting clamp 砂模夾(注塑機使用)air (water) hose 風管,水輪管pressure gauge 高壓油表hydraulic hose 壓力油喉plastic blow mould 吹塑模plastic injection mould 注塑模blandkamp。form pound die 沖扎復合模precisiion blanking die 精密沖模MFR=melt flow rate 熔料流動率MFT=melt flow index 熔料流動指數handling hole 拉鈴孔stop plate 限位塊linder bush 襯套spacer block(plate) 墊塊,方鐵backup ring 背位環standoff 限位塊American Safety Hoist Rings. 英制安全吊裝環Mechanical Properties 機械性能Tensile Strength(MPa) 抗拉強度elongation 延伸率hard
環評公示相關推薦
鄂ICP備17016276號-1