基于51系列單片機的led旋轉顯示器(編輯修改稿)
2024-07-17 12:49 本頁面
【文章內容簡介】 id)interrupt 1）定時器T0的終端服務程序主要是為了把旋轉一周的各個位置分為180分，這樣方便顯示和確定顯示位置及顯示內容。在T0的中斷服務程序中，首先重新給T0賦校正后的初值，然后判斷當前的T0中斷次數，及確定當前顯示的位置，然后再判斷是否改送顯示，如果要送顯示，則調用相應的現實之程序，然后T0中斷次數自加一，最后跳出中斷，詳細參看右流程圖．定時器T1中斷服務程序（void Time_luoji()interrupt 3）因?yàn)樯厦娴腡0的初值不是固定的，所以我們不能再使用T0用做時間運行的標準，要不時間會時快是慢，所以這里我們使用了T1作為時間的運行標準，我們給T1的定時為20毫秒，當產生50個中斷，就是一秒鐘，所以50個中斷，時間秒的值加1。詳細參看流程圖。includeunsigned char code shuzi_0[8]={0x82,0x7C,0x7C,0x7C,0x7C,0x7C,0x82,0xfe}。/*0,0*/unsigned char code shuzi_1[8]={0xfe,0x7e,0x7a,0x00,0x7e,0x7e,0xfe,0xfe}。/*1,1*/unsigned char code shuzi_2[8]={0x3a,0x3c,0x5c,0x5c,0x6c,0x6c,0x72,0xfe}。/*2,2*/unsigned char code shuzi_3[8]={0xba,0x7c,0x7c,0x6c,0x6c,0x6c,0x92,0xfe}。/*3,3*/unsigned char code shuzi_4[8]={0x9e,0xae,0xb6,0xba,0x00,0xbe,0xbe,0xfe}。/*4,4*/unsigned char code shuzi_5[8]={0xa0,0x6c,0x6c,0x6c,0x6c,0x6c,0x9c,0xfe}。/*5,5*/unsigned char code shuzi_6[8]={0x82,0x6c,0x6c,0x6c,0x6c,0x6c,0x9a,0xfe}。/*6,6*/unsigned char code shuzi_7[8]={0xfc,0xfc,0xfc,0x0c,0xf4,0xf8,0xfc,0xfe}。/*7,7*/unsigned char code shuzi_8[8]={0x92,0x6c,0x6c,0x6c,0x6c,0x6c,0x92,0xfe}。/*8,8*/unsigned char code shuzi_9[8]={0xb2,0x6c,0x6c,0x6c,0x6c,0x6c,0x82,0xfe}。/*9,9*/unsigned char code fuhao_A[8]={0xfe,0xfe,0xbb,0xbb,0xfe,0xfe,0xfe,0xfe}。/*:,10*//*******************************************************************************************************************************/unsigned char code hanzi_a[2][16]={0xf7,0x37,0x47,0x70,0x17,0x73,0xb7,0xbd,0xdd,0xdd,0xed,0xe5,0xc9,0xdd,0xbf,0xff, 0xf7,0xe7,0xf7,0xf7,0x00,0xfb,0xbb,0xbd,0xbd,0xbd,0x81,0xbd,0xbc,0x9d,0xbf,0xff}。/*輕*/unsigned char code hanzi_b[2][16]={0xff,0xfb,0xfb,0xfb,0xfb,0xfb,0xfb,0x03,0xfb,0xfb,0xfb,0xfb,0xfb,0xfb,0xff,0xff, 0xdf,0xdf,0xdf,0xdf,0xdf,0xdf,0xdf,0xc0,0xdf,0xdf,0xdf,0xdf,0xdf,0xdf,0xdf,0xff}。/*工*/unsigned char code hanzi_c[2][16]={0xfb,0xcb,0x3d,0xfb,0x3b,0xc3,0xdf,0xef,0xf0,0x17,0xf7,0xf7,0xd7,0xe7,0xff,0xff, 0xef,0xf7,0xf9,0xfe,0x7d,0x73,0xbf,0xcf,0xf3,0xfc,0xf3,0xef,0x9f,0x3f,0xbf,0xff}。/*歡*/unsigned char code hanzi_d[2][16]={0xbf,0xbd,0xbb,0x37,0xff,0x03,0xfb,0xfd,0x7d,0x03,0xfb,0xfb,0xfb,0x01,0xfb,0xff, 0xff,0xbf,0xdf,0xe0,0xdf,0xb8,0xbd,0xbe,0xbf,0x80,0xbf,0xbd,0xbb,0x9c,0xdf,0xff}。/*迎*/unsigned char code hanzi_e[2][16]={0xbf,0xdf,0xef,0x03,0xdc,0xef,0x73,0x98,0xfb,0x0b,0xfb,0xbb,0x6b,0x73,0xff,0xff, 0xbf,0xcf,0xff,0x88,0x7f,0x7e,0x77,0x6d,0x4b,0x7c,0x7f,0x1f,0xff,0xee,0x9f,0xff}。/*您*/unsigned int Tcz,s=0,bt=0。//s表示中斷次數 ，Tcz表示定時器TO的初值unsigned char iDex=0,hiDex=0。 //控制字母和漢字的碼值具體位數unsigned char Hour=10,Minute=15,Second=45,Hour_Flag=0,buffer=0。void hanzi_Show(unsigned char m)。void Time_Show(unsigned char m)。 //數字09加：顯示函數void Time_Amend()。 //時間邏輯控制函數void Hour_Display()。 //小時顯示函數void Minute_Display()。 //分鐘顯示函數void Second_Display()。 //秒鐘顯示函數void A_Display()。 //“：”顯示函數void Init()。 //初始化函數int k=0。void INT00(void)interrupt 0 //外部中斷服務函數，定
教學課件相關推薦
鄂ICP備17016276號-1