【正文】 LACE TOOL PALLET, TOOL NOT AVAILABLE START 請交換供給部工具盤（工具已用完） REPLACE TOOL PALLET, SWITH ATCIVATE START 請交換供給部工具盤（SWITCH ON） CHECK POD START 排出，裝著POD確認 INSERT TOOL INTO COLLET MANUALLY START 手動將工具插入COLLET中（粗徑） REMOVE TOOL INTO COLLET MANUALLY START 手動將COLLET之工具排出（粗徑） ATC CHUCK ALARM(LOWER) START ATC CHUCK異狀（下降端） ATC CHUCK ALARM(UPER) START ATC CHUCK異狀（上升端） CHECK ATC CHUCK NG(LONG) START 檢查ATC CHUCK 鉆針（長） CHECK ATC CHUCK NG (SHORT) START 檢查ATC CHUCK鉆針（短） ALL SPINDLES CANCELLED RESET 全部SPINDLE軸取消 SPINDLE FUSE ALARM START SPINDLE FUSE警報 SPINDLE INVERTER ALARM EMG SPINDLE變頻器警報 LOW AIR PRESSURE START 空壓不足 COLLING UNIT THERMAL ALARM EMG 主軸油冷卻裝置熱電驛警報 COOLING UNIT TEMPERATURE START 主軸油冷卻裝置油溫警報 VACLUM THARMAL ALARM EMG 集塵機熱電驛警報 ATC POINT ALARM START A TC位置警報 BDD ALARM START 斷針警報（BDD） EXTERNAL DEVICE ALARM START 外部裝置警報 FRONT DOOR OPENED START 前門被打開 SAFETY SENSER ALARM 1 START 安全SENSOR警報1 SPINDLE OIL SIGNAL RESET SPINDLE油信號警報 ABC DEVICE ALARM START ABC裝置警報 DRYING UNIT OFF START 空氣干燥機停止中 WORK CLAMP ALART RESET 基板固定CLAMP機能異常檢出 PIN CLAMP ALARM RESET PIN CLAMP機能異常 WORK PRESS ALARM RESET 押板機能動作異常 SAFETY SENSOR ALARM RESET 安全SENSOR警報2 XY AXIS INTERLOCK() EMG X，Y軸連結鎖住() Z AXIS INTERLOCK() EMG Z軸連結鎖住() CUTTING INTERLOCK() EMG 切削連結鎖住() SPINDLE OFF EMG SPINDLE 停止中 MACHIINE LOCK EMG 機械鎖定 WAITING FOR RESET M CODE等待回應 START INHIBIT EMG 啟動停止 WAIT FOR WARMUP SPINDLE EMG SPINDLE暖機中 EXECUTING ABC CYCLE EMG ABC動作中 WAITING FOR OPERATINO START 等待狀態 END OF PROGRAM START 作業完了 PUSHING WORKPRESS EMG 押板機能動作中 ABC NOT READY START 外部裝置ABC未就續 PACK COMMUNICATION ALARM X1112 EMG PACK通訊異常 DEAE STOP ERROR EMG 超極限檢出警報 BDD ALARM RESET 斷針警報(BDD) PRESET SCHEDULE EMG 1V/1W加工異常 SELECTED ILLEGAL MODE RESET 加工模式異常 RECLINNING ALARM RESET 板架柵欄警報(ABC) TOOL ASSINGNMENT ERROR， RESET 工具分配錯誤，檢查工具 CHECK ON TOOL PALLET PAGE 分配頁 X ENCODER ALARM EMG X軸編碼器警報 X OVER SERVO DLOOP EMG X軸伺服回路超出行程 X AXIS INTERLOCK EMG X軸聯結警報 X VELOCTY ALARM EMG X軸速度警報 X REFERENCE POINT ALARM EMG X軸參考點警報 X SERVO ALARM EMG X軸伺服關系警報 Y ENCODER ALARM EMG Y軸編碼器警報 Y OVER SERVO DLOOP EMG Y軸伺服回路超出行程 Y AXIS INTERLOCK EMG Y軸聯結警報 Y VELOCTY ALARM EMG Y軸速度警報 Y REFERENCE POINT ALARM EMG Y軸參考點警報 Y SERVO ALARM EMG Y軸伺服關系警報 Z1 ENCODER ALARM EMG Z1軸編碼器警報 Z1 OVER SERVO DLOOP EMG Z1軸伺服回路超出行程 Z1 AXIS INTERLOCK EMG Z1軸聯結警報 Z1 VELOCTY POINT ALARM EMG Z1軸速度警報 Z1 REFERENCE POINT ALARM EMG Z1軸參考點警報 Z1 SERVO ALARM EMG Z1軸伺服關系警報 Z2 ENCODER ALARM EMG Z2軸編碼器警報 Z2 OVER SERVO DLOOP EMG Z2軸伺服回路超出行程 Z2 AXIS INTERLOCK EMG Z2軸聯結警報 Z2 VELOCTY ALARM EMG Z2軸速度警報 Z2 REFERENCE POINT ALARM EMG Z2軸參考點警報 Z2 SERVO ALARM EMG Z2軸伺服關系警報 Z3 ENCODER ALARM EMG Z3軸編碼器警報 Z3 OVER SERVO DLOOP EMG Z3軸伺服回路超出行程 Z3 AXIS INTERLOCK EMG Z3 軸聯結警報 Z3 VELOCTY ALARM EMG Z3軸速度警報 Z3 REFERENCE POINT ALARM EMG Z3軸參考點警報 Z3 SERVO ALARM EMG Z3軸伺服關系警報 Z4 ENCODER ALARM EMG Z4軸編碼器警報 Z4 OVER SERVO DLOOP EMG Z4軸伺服回路超出行程 Z4 AXIS INTERLOCK EMG Z4軸聯結警報 Z4 VELOCTY ALARM EMG Z4