【正文】 26 Precaution 26 Camera Installation 27 Camera Connections28Chapter 3 Switch Settings29 General29 Switch Setting 29Safeguare 31Troubleshooting32SafeguardBefore install the camera, please read this manual carefully, when install please according to the procedure listed in this manual. You should keep this manual for future use. You must check the power voltage carefully, before power up the camera.Please put the power video and control cables far away from where that is easy to be touched.Do not operate the camera beyond the specified temperature and Humidity. The camera working temperature range is between 0℃ and 50℃. The ambient humidity range is less than 90﹪.Avoid forcibly press violently shake the camera when transporting.To prevent electric shock, do not remove screws or covers. There are no serserviceable parts inside. Ask qualified service personnel for servicing.Video and RS485 cables should be far away from other cables.Never aim it at the sun or other extremely bright objects. Otherwise, blooming or smear may be caused.When clean the camera, please use soft duster cloth. If the camera is very dirty, wipe it off gently with a soft cloth moistened with a weak solution of water and a neutral kitchen detergent. Wring all excess liquid from the cloth before wiping the camera. Next, wipe off all remaining solution with a soft, dry cloth. Use lens cleaning paper to clean the lens.Chapter 1 Overview FeaturesColored Video conference camera is an intelligent video product which conbines light,machinary,electricity, and . It can memorize, auto cruise,fram scan, visca control and IR 64 presets, Baud rate patable with multi mand protocals, it is controlled by the standard RS485/42RS232. This Video confrence camera can be used in video conferencing, builing surveillance, bank sedurity,. longdistance education,ect. . StructureFigure 1 Figure 10Lens 0Sensor for Remote Controller0Power Lamp 0Control Lamp Figure 2Figure 20Camera Address Switch 0Video Jack0S VIDEO Jack0RS232 Jack0RS485/RS422 Jack DC IN 12V Jack1 Baud Rate, Protocol and Image Flip Switch Figure 3Figure 30Camera Address Switch 0Video Jack0RS232 Jack 0RS485/RS422 Jack0DC IN 12V Jack Baud Rate, Protocol and Image Flip Switch . Remote ControllerFigure 40Adrdess code closed0HOME PAN/TILT Init0Address code open0IRIS Control (OPEN Iris Open, CLOSE Iris close)0PAN/TILT CONTROL (up、down、left、right、leftup、leftdown、rightup、rightdown)0Frame Scan0SCAN1 Scan 360176?！?0176。Baud Rate(RS485/422)1200/2400/4800/9600/19200bps、S Video OutputS/N≥50db一、 本公司對于產品提供有限保修各終身維修服務。將吸頂板安裝水泥屋頂上。耗電量10W預置點～70176。分別按照如下方法操作：地址+F1:開啟該地址攝像機遙控器控制功能；地址+F2：關閉該地址攝像機遙控器控制功能。8. 鏡頭光圈控制：按下IRIS光圈亮度鍵可手動控制攝像機鏡頭的光圈大小，要使畫面變得明亮，反復按 OPEN 鍵。0SET設置預置點0數字鍵BACK 保留1POWER 電源鍵1BLC背光補償切換鍵1ZOOM變焦鍵(WIDE遠、TELE近)1FOCUS聚焦鍵(FAR 遠、NEAR 近)1SPEED速度切換鍵1SCAN1掃描180176。2. 在將本設備的開關電源與外接電源連接前，請確認電源電壓值，將電壓調整為AC220V。具有多點目標預置、記憶、自動巡航、區域掃描、輔助開關控制、紅外遙控等功能，64個功能預置點，兼容多種控制協議，波特率可調，采用標準的RS485/42RS232控制方式。6. 攝像機復位控制：按下RESET復位鍵可使攝像機回復初始位置。范圍內往返掃描。吸頂型底板配件圖臺式機安裝連接圖（一）、水平桌面安裝：桌面必須保持水平，將攝像機放置于桌面中間，插入相應連接線；切勿靠近桌面邊沿，以防攝像機跌落。具體設置如下圖所示：SW2碼位1234控制協議OFF OFFOFFOFFONOFFOFFOFFPELCOPOFFONOFFOFFPELCODONONOFFOFFVISCAOFFOFFONOFFONOFFONOFFOFFONONOFF…………碼位567波特率(Bps)1200OFFOFFOFF2400ONOFFOFF4800OFFONOFF9600ONONOFF19200OFFOFFON碼位8圖像正向/翻轉正向OFF翻轉ON控制協議、波特率、圖像正向/翻轉設置圖4．VISCA協議設置：設置攝像機地址為1，波特率為9600BPS，控制協議為VISCA，圖像正向：SW2碼 位12345678碼位狀態ONONOFFOFFONONOFFOFF即將碼位6設置為“ON”，將其余碼位設置為“OFF”就可實現。,Tilt 30～90176。0～95%（ noncondensation ）～50176。 Press the TELE button the camera’s focus length will change to long and view angle turn small, you can see distant object. Camera reset: Press RESET button, the camera will reset and reinitialize pan tile and lens.Back light ON/OFF control:When one portion of an image is brilliantly bright while other portions are dark, the video will bee dark, you can improve the video quality by turn on the backlight pensation function. Press BLC ON will make the camera switch to BLC ON mode. Press BLC OFF will make the camera switch to BLC OF mode. IRIS control: Press IRIS OPEN button, the camera’s IRIS will bee large and the video will bee bright, Press IRIS CLOSE button, the camera’s IRIS will bee small and the video will bee dark.Preset control:Th