【正文】 ecreate zonename,ali_name。 2,3。 2,3。export TMPDIR ＃建立一個臨時交換空間 9./ ＃安裝軟件f) 確認安裝成功，可以打開管理界面在其界面上觀察光纖卡的狀態。(On x86, Solaris , you will see name=cmdk.)We use the parent keyword to ensure that Solaris specifically probes all adapters controlled by the lpfc driver for the specified targets and LUNs.Note that changes to a target driver39。all39。即使是與本章描述相同型號的光纖卡安裝，由于產品的批號有可能不同，安裝方法也有可能存在差異，所以安裝時一定要仔細閱讀光纖卡的安裝說明，注意是否有特殊要求。Network hostname (for first adapter) [?,q]: 請輸入該主機的主機名。We use the class keyword to ensure that Solaris specifically probes all adapters controlled by all drivers, that register themselves as class=scsi, for the specified targets and LUNs. The lpfc driver registers itself as class=scsiThe installation procedure for lpfc automatically updates or to search for Fibre Channel disk drives. The instructions added to the configuration file look like this: 7name=sd parent=lpfc target=0 lun=0。name=sd parent=lpfc target=25 lun=0。gateway=，請按照如下步驟操作IBM_3534_FC_Switch:admin ipaddrsetEther IP Address []: Ether Submask []: Fibre Channel IP Address [none]:Fibre Channel Submask []:Gateway Address [none]: Set IP addresses now?[y = set now, n = next reboot]: yIBM_3534_FC_Switch:admin. 通過 LED 指示燈了解光纖交換機連接狀況 LED指示燈介紹（以 brocade 3200為例）a) 電源燈（Switch Power LED）： 在交換機的前面板上b) 端口狀態燈（Port Status LED）：在每個端口的左上方c) 端口速率燈（Port Speed LED）：在每個端口的右上方d) 以太網速率燈（Ether Speed LED）：在交換機的前面板上 12e) 以太網活動燈（Ether Activity LED）：在交換機的前面板上f) 端口準備就緒燈（Port Readiness LED ）：在交換機的后面板上. 光纖交換機指示燈含義下面主要介紹端口狀態和速率燈LED燈 LED燈顏色 硬件狀態端口速率燈 常綠 2G常滅 1G端口狀態燈 常綠 連接正常，沒有數據傳輸常橙 收到光信號，沒有online常滅 沒有光信號. 光纖交換機常用命令作用：提供幫助IBM_3534_FC_Switch:admin helpagtcfgSet Set SNMP agent configurationagtcfgShow Print SNMP agent configurationagtcfgDefault Reset SNMP agent to factory defaultaliasShow Print Alias Server informationbackSpace Set/clear alternate backspace charbsn Display/set Brocade serial numberconfigure Set switch config parametersconfigShow Print switch config parametersconfigDefault Reset config to factory defaultconfigDownload Load switch config from a serverconfigUpload Save switch config to a serverdate Print/set the system date and timeerrDump Print error log (no page breaks)errShow Print error logfabricShow Print fabric membership infofaShow Display Fabric Assist infofaStatsShow Display Fabric Assist StatisticsfanShow Print fan statusfastboot Reboot this switch, bypassing POST 13firmwareDownload Download firmware into switchfpgaDownload Download FPGA list into switchType CR to continue, QCR to stop:具體命令幫助，用法：help mandIBM_3534_FC_Switch:admin help nsshowNAME nsShow display local Name Server informationSYNOPSIS nsShowAVAILABILITY all usersDESCRIPTION This mand displays local Name Server information, which includes information about devices connected to this switch, and cached information about devices connected to other switches in the Fabric. The message There is no entry in the Local Name Server is displayed if there is no information in this switch, but there still may be devices connected to other switches in the Fabric. The mand nsAllShow shows information from all switches. Each line of output s