【正文】 ........9 模具的概要設計......................................................9 凹模的設計..........................................................9 材料及熱處理..................................................9 凹模的結構與尺寸..............................................9 凸模的設計.........................................................10 材料及熱處理.................................................10 凸模的結構與尺寸.............................................10 凸模高度計算.................................................11 橡膠..............................................................12 凹模支架..........................................................12 固定塊............................................................13 定位銷............................................................13 底座..............................................................14 支座..............................................................15 其他零件.........................................................16 旋入式模柄.................................................16 彈簧.......................................................17 六角螺母...................................................17 螺釘.......................................................17 圓柱銷.....................................................17 固定板.....................................................17第4章 模具的裝配........................................................18......................................................18....................................................18....................................................18第5章 設備的選擇........................................................19......................................................19......................................................20....................................................20..........................................20結論......................................................................21參考文獻..................................................................22致謝......................................................................23附錄......................................................................24IV前言沖壓加工技術應用范圍十分廣泛，在國民經濟各工業部門中，幾乎都有沖壓加工或沖壓產品的生產。plete all the necessary process calculations,including the size of the die edge,each station rushed pressure,total stamping process force,pressure center。在設計時廣泛吸收了國內外各個領域成熟的經驗和最新的參考資料，并在模具的成型零部件等關鍵部位采用了國內外的優質模具鋼。所以該零件具有較好的可沖壓性。沖裁力是設計模具、選擇壓力機的重要參數?？倹_壓力F0= （） 壓力中心計算。因而沖孔時，應以凸模為基準。凸、凹模刃口尺寸的計算方法基本上可分為兩類：分別加工與配合加工。在結構設計中概要設計是模具結構設計的開始，根據產品零件要求，確定沖孔模具的基本結構框架。 橡膠本模具采用了彈性卸料裝置，考慮卸料力的問題在前面算過了，厚度為30mm的橡膠，具體計算如下（1）確定橡膠的自由高度 H自由=（~4）S工作 （）式中：S工作=t+S修磨+1，t為材料厚度S修磨一般取4~6mmS工作=+5+1=